have timer support
* Default timer size should be a long, not an int. Int will roll over way
too fast, with no performance benifit on 64 bit machines...
This commit was SVN r25501.
https://svn.open-mpi.org/trac/ompi/wiki/ProcessPlacement
The wiki page is incomplete at the moment, but I hope to complete it over the next few days. I will provide updates on the devel list. As the wiki page states, the default and most commonly used options remain unchanged (except as noted below). New, esoteric and complex options have been added, but unless you are a true masochist, you are unlikely to use many of them beyond perhaps an initial curiosity-motivated experimentation.
In a nutshell, this commit revamps the map/rank/bind procedure to take into account topology info on the compute nodes. I have, for the most part, preserved the default behaviors, with three notable exceptions:
1. I have at long last bowed my head in submission to the system admin's of managed clusters. For years, they have complained about our default of allowing users to oversubscribe nodes - i.e., to run more processes on a node than allocated slots. Accordingly, I have modified the default behavior: if you are running off of hostfile/dash-host allocated nodes, then the default is to allow oversubscription. If you are running off of RM-allocated nodes, then the default is to NOT allow oversubscription. Flags to override these behaviors are provided, so this only affects the default behavior.
2. both cpus/rank and stride have been removed. The latter was demanded by those who didn't understand the purpose behind it - and I agreed as the users who requested it are no longer using it. The former was removed temporarily pending implementation.
3. vm launch is now the sole method for starting OMPI. It was just too darned hard to maintain multiple launch procedures - maybe someday, provided someone can demonstrate a reason to do so.
As Jeff stated, it is impossible to fully test a change of this size. I have tested it on Linux and Mac, covering all the default and simple options, singletons, and comm_spawn. That said, I'm sure others will find problems, so I'll be watching MTT results until this stabilizes.
This commit was SVN r25476.
since the 1.4 release (and configure would abort when run with sparc v8), but
the code was left in place. Sparc v9 (32 or 64 bit) are still supported
targets.
This commit was SVN r25258.
1 otherwise. It was doing the opposite, so this patch fixes the
return values. All uses (all in ORTE) used the actual return values,
not the documented values, so fix them as well.
This commit was SVN r25257.
Fix a bug in the new code that prevented the system from correctly matching addresses.
Remove comments in the show-help text indicating that we would continue in the face of incorrect specifications - leave that to the calling layer to decide.
Modify the new opal_ifmatches so it returns error codes letting the caller better understand the result.
Modify the oob to ensure we abort if we don't find interfaces matching specified constraints, and that we do so without multiple error messages.
NOTE: we have a conflict in our standards. We have been using comma-delimited lists of interfaces for all our params. However, one param - opal_net_private_ipv4 - now uses semicolons instead of comma separators. No idea why, but it is confusing.
This commit was SVN r24755.
Correctly check the dependencies of MSYS env.
Set up configure include and lib path for building the package.
update a few more CMake scripts.
This commit was SVN r24663.
OMPI supports multiple different repository systems (SVN, hg, git).
But the VERSION file has listed "want_svn" and "svn_r" as fields, even
though the actual repo system and version may not be SVN.
So search/replace those fields (and derrivative values that come from
those fields) with "want_repo_rev" and "repo_rev", respectively.
This commit was SVN r24405.
This merges the branch containing the revamped build system based around converting autogen from a bash script to a Perl program. Jeff has provided emails explaining the features contained in the change.
Please note that configure requirements on components HAVE CHANGED. For example. a configure.params file is no longer required in each component directory. See Jeff's emails for an explanation.
This commit was SVN r23764.
do the right thing. They now properly return
the value after the update. This also fixes all warnings
reported by the Sun Studio compiler. George provided the
new assembly routines. I added some configure code to make
sure the compilers could handle it.
This fixes trac:2560.
This commit was SVN r23721.
The following Trac tickets were found above:
Ticket 2560 --> https://svn.open-mpi.org/trac/ompi/ticket/2560
#define CACHE_LINE_SIZE to 128. This name has a conflict on NetBSD,
and it seems kinda odd to have a header file that ''only'' defines a
single value. Also, we'll soon be raising hwloc to be a first-class
item, so having this file around seemed kinda weird.
Therefore, I replaced CACHE_LINE_SIZE with opal_cache_line_size, an
int (in opal/runtime/opal_init.c and opal/runtime/opal.h) on the
rationale that we can fill this in at runtime with hwloc info (trunk
and v1.5/beyond, only). The only place we ''needed'' a compile-time
CACHE_LINE_SIZE was in the BTL SM (for struct padding), so I made a
new BTL_SM_ preprocessor macro with the old CACHE_LINE_SIZE value
(128). That use isn't suitable for run-time hwloc information,
anyway.
This commit was SVN r23349.
* Remove OPAL_ERR_PAFFINITY_NOT_SUPPORTED; fit it into the generic
OPAL_ERR_NOT_SUPPORTED case.
* When odls_default detects that processor affinity is not supported,
it prints a specific message about it, and then it suppressed a
generic HNP help message that would normally follow it (i.e., it's
easier to have the "processor affinity is not supported" show_help
message last).
* Use some symbolic names in odls_default instead of fixed int's,
just for slight readability improvements in the code.
* Introduce orte_show_help_suppress(), which gives the ability to
suppress any future showings of any arbitrary show_help() message.
This is useful if you display message X and want to suppress
message Y. This suppression *only* works in environments where
orte_show_help() does coalescing.
This commit was SVN r23249.
It is okay to not have a paffinity module IF you aren't using paffinity anyway. So don't error out of MPI_Init because a paffinity module wasn't selected.
Cleanup error reporting in the odls default module to (once and for all!) eliminate messages originating in the fork'd process. Create some new error codes to allow us to pass enough info back to the parent process to provide useful error messages.
This commit was SVN r23106.
and opal_atomic_lifo_pop. Adds memory barriers to remove the race
condition
This commit was SVN r23014.
The following Trac tickets were found above:
Ticket 2355 --> https://svn.open-mpi.org/trac/ompi/ticket/2355
to Eugene, Jeff, and Briand for the help. This patch is supposed to
fix several outstanding issues, notably the one on tickets #2043.
This commit was SVN r22324.
#if defined (c_plusplus)
defined (__cplusplus)
followed by
extern "C" {
and the closing counterpart by BEGIN_C_DECLS and END_C_DECLS.
Notable exceptions are:
- opal/include/opal_config_bottom.h:
This is our generated code, that itself defines BEGIN_C_DECL and
END_C_DECL
- ompi/mpi/cxx/mpicxx.h:
Here we do not include opal_config_bottom.h:
- Belongs to external code:
opal/mca/backtrace/darwin/MoreBacktrace/MoreDebugging/MoreBacktrace.c
opal/mca/backtrace/darwin/MoreBacktrace/MoreDebugging/MoreBacktrace.h
- opal/include/opal/prefetch.h:
Has C++ specific macros that are protected:
- Had #if ... } #endif _and_ END_C_DECLS (aka end up with 2x
END_C_DECLS)
ompi/mca/btl/openib/btl_openib.h
- opal/event/event.h has #ifdef __cplusplus as BEGIN_C_DECLS...
- opal/win32/ompi_process.h: had extern "C"\n {...
opal/win32/ompi_process.h: dito
- ompi/mca/btl/pcie/btl_pcie_lex.l: needed to add *_C_DECLS
ompi/mpi/f90/test/align_c.c: dito
- ompi/debuggers/msgq_interface.h: used #ifdef __cplusplus
- ompi/mpi/f90/xml/common-C.xsl: Amend
Tested on linux using --with-openib and --with-mx
The following do not contain either opal_config.h, orte_config.h or
ompi_config.h
(but possibly other header files, that include one of the above):
ompi/mca/bml/r2/bml_r2_ft.h
ompi/mca/btl/gm/btl_gm_endpoint.h
ompi/mca/btl/gm/btl_gm_proc.h
ompi/mca/btl/mx/btl_mx_endpoint.h
ompi/mca/btl/ofud/btl_ofud_endpoint.h
ompi/mca/btl/ofud/btl_ofud_frag.h
ompi/mca/btl/ofud/btl_ofud_proc.h
ompi/mca/btl/openib/btl_openib_mca.h
ompi/mca/btl/portals/btl_portals_endpoint.h
ompi/mca/btl/portals/btl_portals_frag.h
ompi/mca/btl/sctp/btl_sctp_endpoint.h
ompi/mca/btl/sctp/btl_sctp_proc.h
ompi/mca/btl/tcp/btl_tcp_endpoint.h
ompi/mca/btl/tcp/btl_tcp_ft.h
ompi/mca/btl/tcp/btl_tcp_proc.h
ompi/mca/btl/template/btl_template_endpoint.h
ompi/mca/btl/template/btl_template_proc.h
ompi/mca/btl/udapl/btl_udapl_eager_rdma.h
ompi/mca/btl/udapl/btl_udapl_endpoint.h
ompi/mca/btl/udapl/btl_udapl_mca.h
ompi/mca/btl/udapl/btl_udapl_proc.h
ompi/mca/mtl/mx/mtl_mx_endpoint.h
ompi/mca/mtl/mx/mtl_mx.h
ompi/mca/mtl/psm/mtl_psm_endpoint.h
ompi/mca/mtl/psm/mtl_psm.h
ompi/mca/pml/cm/pml_cm_component.h
ompi/mca/pml/csum/pml_csum_comm.h
ompi/mca/pml/dr/pml_dr_comm.h
ompi/mca/pml/dr/pml_dr_component.h
ompi/mca/pml/dr/pml_dr_endpoint.h
ompi/mca/pml/dr/pml_dr_recvfrag.h
ompi/mca/pml/example/pml_example.h
ompi/mca/pml/ob1/pml_ob1_comm.h
ompi/mca/pml/ob1/pml_ob1_component.h
ompi/mca/pml/ob1/pml_ob1_endpoint.h
ompi/mca/pml/ob1/pml_ob1_rdmafrag.h
ompi/mca/pml/ob1/pml_ob1_recvfrag.h
ompi/mca/pml/v/pml_v_output.h
opal/include/opal/prefetch.h
opal/mca/timer/aix/timer_aix.h
opal/util/qsort.h
test/support/components.h
This commit was SVN r21855.
The following SVN revision numbers were found above:
r2 --> open-mpi/ompi@58fdc18855
OMPI_* to OPAL_*. This allows opal layer to be used more independent
from the whole of ompi.
NOTE: 9 "svn mv" operations immediately follow this commit.
This commit was SVN r21180.
size. The correct way is to cast to an integer type that has the same length, and
then allow the compiler to upgrade to the read type.
This commit was SVN r19944.
but not anything in libc. Which causes an incorrect answer for
AC_CHECK_FUNCS. Work around that by also checking for the
#define.
This commit was SVN r18730.
* The opal_sys_timer_get_cycles() call was implemented for
Sparc v9 using inline assembly, but not in the assembly files.
This would only currently matter on Linux Sparc systems using
a compiler that didn't support inline assembly (not many of
those), but it should be there for completion.
* The linux timer component would always build on non-Alpha
platforms, rather than only building on platforms where
opal_sys_timer_get_cycles() was implemented. This would
only matter on a very narrow set of platforms that we don't
really support, but still, it could be more right. We now
only build the component on platforms where we have the
assembly call to get the cycle counter.
* Added a comment to opal/sys/timer.h to note that the linux
timer component needed to be updated if another platform was
added.
This should be harmless to commit. It will only really change
behaviors on platforms we don't have assembly support for, which
currently won't make it through configure. It really only matters
when (if?) we support atomic operations through libatomic_ops.
This commit was SVN r17887.
