Remove all architecture references from ORTE and put them back in the modex using modex_send/recv calls.
Hetero operations are now fully supported again. Comm_spawn now works up to the point where it segfaults due to an error in the CID code - which now allows Edgar to dig further! :-)
This commit was SVN r21655.
- Add a CMake macro for checking OPAL_MAX_XXX values, re-written from OPAL_WITH_OPTION_MIN_MAX_VALUE m4 function.
- Definition prefix changes and additional datatype alignments checking.
- Finish the datatype splitting on Windows too. :-)
This commit was SVN r21649.
The following SVN revision numbers were found above:
r21641 --> open-mpi/ompi@6c5532072a
r21642 --> open-mpi/ompi@c971c09eb6
OMPI
and a language agnostic part in OPAL. The convertor is completely
moved into OPAL. This offers several benefits as described in RFC
http://www.open-mpi.org/community/lists/devel/2009/07/6387.php
namely:
- Fewer basic types (int* and float* types, boolean and wchar
- Fixing naming scheme to ompi-nomenclature.
- Usability outside of the ompi-layer.
- Due to the fixed nature of simple opal types, their information is
completely
known at compile time and therefore constified
- With fewer datatypes (22), the actual sizes of bit-field types may be
reduced
from 64 to 32 bits, allowing reorganizing the opal_datatype
structure, eliminating holes and keeping data required in convertor
(upon send/recv) in one cacheline...
This has implications to the convertor-datastructure and other parts
of the code.
- Several performance tests have been run, the netpipe latency does not
change with
this patch on Linux/x86-64 on the smoky cluster.
- Extensive tests have been done to verify correctness (no new
regressions) using:
1. mpi_test_suite on linux/x86-64 using clean ompi-trunk and
ompi-ddt:
a. running both trunk and ompi-ddt resulted in no differences
(except for MPI_SHORT_INT and MPI_TYPE_MIX_LB_UB do now run
correctly).
b. with --enable-memchecker and running under valgrind (one buglet
when run with static found in test-suite, commited)
2. ibm testsuite on linux/x86-64 using clean ompi-trunk and ompi-ddt:
all passed (except for the dynamic/ tests failed!! as trunk/MTT)
3. compilation and usage of HDF5 tests on Jaguar using PGI and
PathScale compilers.
4. compilation and usage on Scicortex.
- Please note, that for the heterogeneous case, (-m32 compiled
binaries/ompi), neither
ompi-trunk, nor ompi-ddt branch would successfully launch.
This commit was SVN r21641.
point, the event engine has been shut down until btl finalization is
done, so opal_progress in the wait loop is not an option - we have
to drain from inside the btl.
Clean up the looping structure for the finalize routine
Update copyrights.
This commit was SVN r21620.
different processes have requested different levels of thread support. This
verification is restricted to MPI_COMM_WORLD.
In case one ore more processes have requested support for MPI_THREAD_MULTIPLE,
the cid selection algorithm will fall back to the original, thread safe
approach. Else, it uses the block-algorithm.
For dynamic communicators, we always fall back now to the original algorithm.
This has been tested for homogeneous and heterogeneous settings for
MCW. However, I could not test yet the dynamic comm scenario for technical
reasons, and that's why I don't close yet ticket 1949.
This commit was SVN r21613.
IPv4 and IPv6) is outside the legal boundaries. This fixes trac:1869.
This commit was SVN r21612.
The following Trac tickets were found above:
Ticket 1869 --> https://svn.open-mpi.org/trac/ompi/ticket/1869
(also usable to check validation of a trace)
- removed OTF python bindings
(a working version of the OTF python bindings are available in the latest stand-alone release;
see http://www.tu-dresden.de/zih/otf/)
- incremented OTF version number
This commit was SVN r21601.
