This is required to tighten up the BTL semantics. Ordering is not guaranteed,
but, if the BTL returns a order tag in a descriptor (other than
MCA_BTL_NO_ORDER) then we may request another descriptor that will obey
ordering w.r.t. to the other descriptor.
This will allow sane behavior for RDMA networks, where local completion of an
RDMA operation on the active side does not imply remote completion on the
passive side. If we send a FIN message after local completion and the FIN is
not ordered w.r.t. the RDMA operation then badness may occur as the passive
side may now try to deregister the memory and the RDMA operation may still be
pending on the passive side.
Note that this has no impact on networks that don't suffer from this
limitation as the ORDER tag can simply always be specified as
MCA_BTL_NO_ORDER.
This commit was SVN r14768.
We eagerly send data up to btl_*_eager_limit with the match
Upon ACK of the MATCH we start using send/receives of size
btl_*_max_send_size up to the btl_*_rdma_pipeline_offset
After the btl_*_rdma_pipeline_offset we begin using RDMA writes of
size btl_*_rdma_pipeline_frag_size.
Now, on a per message basis we only use the above protocol if the
message is larger than btl_*_min_rdma_pipeline_size
btl_*_eager_limit - > same
btl_*_max_send_size -> same
btl_*_rdma_pipeline_offset -> btl_*_min_rdma_size
btl_*_rdma_pipeline_frag_size -> btl_*_max_rdma_size
btl_*_min_rdma_pipeline_size is new..
This patch also moves all BTL common parameters initialisation into
btl_base_mca.c file.
This commit was SVN r14681.
computation of the current location on the pack/unpack process. This can
be used both for retrieving the pointer to the first byte (in the special
case of the cached RDMA protocol) and for getting the current
position (for the pipelined protocol).
I modified all BTLs, but most of them are still untested.
This commit was SVN r14180.
This merge adds Checkpoint/Restart support to Open MPI. The initial
frameworks and components support a LAM/MPI-like implementation.
This commit follows the risk assessment presented to the Open MPI core
development group on Feb. 22, 2007.
This commit closes trac:158
More details to follow.
This commit was SVN r14051.
The following SVN revisions from the original message are invalid or
inconsistent and therefore were not cross-referenced:
r13912
The following Trac tickets were found above:
Ticket 158 --> https://svn.open-mpi.org/trac/ompi/ticket/158
and another for dst descriptors. This provide partial solution to OB1 protocol
deadlock problem. We can limit number of RDMA descriptors (by setting
btl_openib_free_list_max to something different from -1) and if we will be
lucky to hit this limit before we fail to register more memory the protocol
will not deadlock. When we had only one list for src/dst descriptors we
deadlocked when we reached max limit for the list.
This commit was SVN r13844.
we are looking at subnet_id's and we are counting active ports per subnet.
move subnet count out of procs loop,, no need to do it there...
This commit was SVN r13105.
George wrote the initial patch, I extended it slightly and am responsible for all bugs found.
Refs trac:587
This commit was SVN r13023.
The following Trac tickets were found above:
Ticket 587 --> https://svn.open-mpi.org/trac/ompi/ticket/587
This is somewhat limited currently for expample, if you have 3 ports on Node A and 5 ports
on Node B then the peers will use 3 ports to communicate with each other.
This is on a subnet basis, so for any pair of nodes we take the
intersection of the available ports within a subnet.
We use subnets to determine reachability for lazy connection establishment. So
if Node A and Node B each have two HCA's (on seperate networks) then the
subnet's must be distinct, otherwise we will try to wire up HCA's on seperate
networks.
This commit was SVN r12978.
* Make sure that the pval always writes to the correct portion of the
lval. This only matters on 32 bit big endian machines.
* On 32 bit machines when assigning to pval, the other 4 bytes of lval
weren't being written, which could lead to bogus data
We use macros so that there aren't casts all over the code and the pval
assignment can occur to the correct 4 bytes. Refs trac:587
This commit was SVN r12974.
The following Trac tickets were found above:
Ticket 587 --> https://svn.open-mpi.org/trac/ompi/ticket/587
udapl/openib/vapi/gm mpools a deprecated. rdma mpool has parameter that allows
to limit its size mpool_rdma_rcache_size_limit (default is 0 - unlimited).
This commit was SVN r12878.
allocation logic is completely done outside the data-type engine (in the PML) there is
no need for any special case inside the data-type engine. There is less arguments for
the ompi_convertor_pack and ompi_convertor_unpack as well (the last field free_after is
not required anymore as there is no memory allocated in the engine itself). This change
affect all components using datatypes. I test most of them, but it might happens that I
miss some ... If it's the case please let me know (don't shoot the pianist!!).
This commit was SVN r12331.
In order to provide backwards compatability the framework versions are bumped
and the handler registeration function is at the end of the btl struct.
Testing done on sm, openib, and gm..
This commit was SVN r11256.
the upperlayer assynchronously although there are some issues with this.. such
as there are multiple consumers of the btl's.. who get's the
This commit was SVN r11232.
of send/receives outstanding.
Use ibv_cq_resize if available after initial creation of completion queue if
cq_size is too small (based on number of peers).
This commit was SVN r11053.
- move files out of toplevel include/ and etc/, moving it into the
sub-projects
- rather than including config headers with <project>/include,
have them as <project>
- require all headers to be included with a project prefix, with
the exception of the config headers ({opal,orte,ompi}_config.h
mpi.h, and mpif.h)
This commit was SVN r8985.
