b225366012
passed to make it all flow thru the opal/pmix "put/get" operations. Update the PMIx code to latest master to pickup some required behaviors. Remove the no-longer-required get_contact_info and set_contact_info from the RML layer. Add an MCA param to allow the ofi/rml component to route messages if desired. This is mainly for experimentation at this point as we aren't sure if routing wi ll be beneficial at large scales. Leave it "off" by default. Signed-off-by: Ralph Castain <rhc@open-mpi.org>
116 строки
3.5 KiB
Plaintext
116 строки
3.5 KiB
Plaintext
# -*- text -*-
|
|
#
|
|
# Copyright (c) 2004-2006 The Trustees of Indiana University and Indiana
|
|
# University Research and Technology
|
|
# Corporation. All rights reserved.
|
|
# Copyright (c) 2004-2006 The University of Tennessee and The University
|
|
# of Tennessee Research Foundation. All rights
|
|
# reserved.
|
|
# Copyright (c) 2004-2005 High Performance Computing Center Stuttgart,
|
|
# University of Stuttgart. All rights reserved.
|
|
# Copyright (c) 2004-2005 The Regents of the University of California.
|
|
# All rights reserved.
|
|
# Copyright (c) 2014-2017 Intel, Inc. All rights reserved.
|
|
# Copyright (c) 2015 Cisco Systems, Inc. All rights reserved.
|
|
# $COPYRIGHT$
|
|
#
|
|
# Additional copyrights may follow
|
|
#
|
|
# $HEADER$
|
|
#
|
|
[static-and-dynamic]
|
|
Both static and dynamic port ranges were specified for the
|
|
out-of-band (OOB) communication subsystem:
|
|
|
|
Static ports: %s
|
|
Dynamic ports: %s
|
|
|
|
Only one can be specified. Please choose either static or
|
|
dynamic ports and try again.
|
|
#
|
|
[include-exclude]
|
|
Both TCP interface include and exclude lists were specified:
|
|
|
|
Include: %s
|
|
Exclude: %s
|
|
|
|
Only one of these can be given.
|
|
#
|
|
[not-parseable]
|
|
The specified network is not parseable. Since we cannot determine
|
|
your desired intent, we cannot establish a TCP socket for out-of-band
|
|
communications and will therefore abort. Please correct the network
|
|
specification and retry.
|
|
#
|
|
[no-included-found]
|
|
None of the TCP networks specified to be included for out-of-band communications
|
|
could be found:
|
|
|
|
Value given: %s
|
|
|
|
Please revise the specification and try again.
|
|
#
|
|
[excluded-all]
|
|
The specified list of networks to be excluded for TCP out-of-band communications
|
|
resulted in no networks being available:
|
|
|
|
Value given: %s
|
|
|
|
Please revise the specification and try again.
|
|
#
|
|
[invalid if_inexclude]
|
|
WARNING: An invalid value was given for oob_tcp_if_%s. This
|
|
value will be ignored.
|
|
|
|
Local host: %s
|
|
Value: %s
|
|
Message: %s
|
|
#
|
|
[authent-fail]
|
|
An attempt was made to make a TCP connection between two hosts:
|
|
|
|
Initiating host: %s
|
|
Receiving host: %s
|
|
|
|
Unfortunately, the connection was refused due to a failure to
|
|
authenticate. This is usually caused by a mis-match between
|
|
the security domains of the two hosts - e.g., one might be
|
|
using Munge while the other is not. This can typically be
|
|
resolved by specifying the desired security method. For
|
|
example, adding "--mca sec basic" to your command line.
|
|
#
|
|
[accept failed]
|
|
WARNING: The accept(3) system call failed on a TCP socket. While this
|
|
should generally never happen on a well-configured HPC system, the
|
|
most common causes when it does occur are:
|
|
|
|
* The process ran out of file descriptors
|
|
* The operating system ran out of file descriptors
|
|
* The operating system ran out of memory
|
|
|
|
Your Open MPI job will likely hang until the failure resason is fixed
|
|
(e.g., more file descriptors and/or memory becomes available), and may
|
|
eventually timeout / abort.
|
|
|
|
Local host: %s
|
|
Errno: %d (%s)
|
|
Probable cause: %s
|
|
#
|
|
[privilege failure]
|
|
An attempt was made to initiate a TCP connection from an
|
|
unprivileged source while we are operating at privileged
|
|
levels.
|
|
|
|
Local host: %s
|
|
Listening port: %d
|
|
Remote host: %s
|
|
Remote port: %d
|
|
|
|
|
|
The connection was rejected.
|
|
#
|
|
[static-fwd]
|
|
Static ports were requested while orte_fwd_mpirun_port was set.
|
|
Both options cannot be simultaneously set. Please either set
|
|
orte_fwd_mpirun_port=false or remove any static port directives.
|