than just the PML/BTLs these days. Also clean up the code so that it
handles the situation where not all nodes register information for a given
node (rather than just spinning until that node sends information, like
we do today).
Includes r15234 and r15265 from the /tmp/bwb-modex branch.
This commit was SVN r15310.
The following SVN revisions from the original message are invalid or
inconsistent and therefore were not cross-referenced:
r15234
r15265
This is required to tighten up the BTL semantics. Ordering is not guaranteed,
but, if the BTL returns a order tag in a descriptor (other than
MCA_BTL_NO_ORDER) then we may request another descriptor that will obey
ordering w.r.t. to the other descriptor.
This will allow sane behavior for RDMA networks, where local completion of an
RDMA operation on the active side does not imply remote completion on the
passive side. If we send a FIN message after local completion and the FIN is
not ordered w.r.t. the RDMA operation then badness may occur as the passive
side may now try to deregister the memory and the RDMA operation may still be
pending on the passive side.
Note that this has no impact on networks that don't suffer from this
limitation as the ORDER tag can simply always be specified as
MCA_BTL_NO_ORDER.
This commit was SVN r14768.
Per discussions with Brian and Ralph, make a slight correction in
where components are installed. Use $pkglibdir, not $libdir/openmpi,
so that when compiled in the orte trunk, components are installed to
the right directory (because the component search patch is checking
$pkglibdir).
This commit was SVN r14345.
The following SVN revisions from the original message are invalid or
inconsistent and therefore were not cross-referenced:
r14289
computation of the current location on the pack/unpack process. This can
be used both for retrieving the pointer to the first byte (in the special
case of the cached RDMA protocol) and for getting the current
position (for the pipelined protocol).
I modified all BTLs, but most of them are still untested.
This commit was SVN r14180.
This merge adds Checkpoint/Restart support to Open MPI. The initial
frameworks and components support a LAM/MPI-like implementation.
This commit follows the risk assessment presented to the Open MPI core
development group on Feb. 22, 2007.
This commit closes trac:158
More details to follow.
This commit was SVN r14051.
The following SVN revisions from the original message are invalid or
inconsistent and therefore were not cross-referenced:
r13912
The following Trac tickets were found above:
Ticket 158 --> https://svn.open-mpi.org/trac/ompi/ticket/158
- mca_base_param_file_prefix
(Default: NULL)
This is the fullname of the "-am" mpirun option. Used to specify a ':'
separated list of AMCA parameter set files.
- mca_base_param_file_path
(Default: $SYSCONFDIR/amca-param-sets/:$CWD)
The path to search for AMCA files with relative paths. A warning will be
printed if the AMCA file cannot be found.
* Added a new function "mca_base_param_recache_files" the re-reads the file
configurations. This is used internally to help bootstrap the MCA system.
* Added a new orterun/mpirun command line option '-am' that aliases for the
mca_base_param_file_prefix MCA parameter
* Exposed the opal_path_access function as it is generally useful in other
places in the code.
* New function "opal_cmd_line_make_opt_mca" which will allow you to append a
new command line option with MCA parameter identifiers to set at the same
time. Previously this could only be done at command line declaration time.
* Added a new directory under the $pkgdatadir named "amca-param-sets" where all
the 'shipped with' Open MPI AMCA parameter sets are placed. This is the first
place to search for AMCA sets with relative paths.
* An example.conf AMCA parameter set file is located in
contrib/amca-param-sets/.
* Jeff Squyres contributed an OpenIB AMCA set for benchmarking.
Note: You will need to autogen with this commit as it adds a configure param.
Sorry :(
This commit was SVN r13867.
it may contain garbage and we will try to unregister it later in btl_free().
This commit was SVN r13054.
The following Trac tickets were found above:
Ticket 729 --> https://svn.open-mpi.org/trac/ompi/ticket/729
components that use configure.m4 for configuration or are always built.
The macro has not been needed since moving to configure types other than
configure.stub
Fixes trac:590
This commit was SVN r13031.
The following Trac tickets were found above:
Ticket 590 --> https://svn.open-mpi.org/trac/ompi/ticket/590
* Make sure that the pval always writes to the correct portion of the
lval. This only matters on 32 bit big endian machines.
* On 32 bit machines when assigning to pval, the other 4 bytes of lval
weren't being written, which could lead to bogus data
We use macros so that there aren't casts all over the code and the pval
assignment can occur to the correct 4 bytes. Refs trac:587
This commit was SVN r12974.
The following Trac tickets were found above:
Ticket 587 --> https://svn.open-mpi.org/trac/ompi/ticket/587
if the remote architecture differs from the local architecture and the
btl doesn't support heterogeneous transport.
Refs trac:587
This commit was SVN r12879.
The following Trac tickets were found above:
Ticket 587 --> https://svn.open-mpi.org/trac/ompi/ticket/587
allocation logic is completely done outside the data-type engine (in the PML) there is
no need for any special case inside the data-type engine. There is less arguments for
the ompi_convertor_pack and ompi_convertor_unpack as well (the last field free_after is
not required anymore as there is no memory allocated in the engine itself). This change
affect all components using datatypes. I test most of them, but it might happens that I
miss some ... If it's the case please let me know (don't shoot the pianist!!).
This commit was SVN r12331.
In order to provide backwards compatability the framework versions are bumped
and the handler registeration function is at the end of the btl struct.
Testing done on sm, openib, and gm..
This commit was SVN r11256.
the upperlayer assynchronously although there are some issues with this.. such
as there are multiple consumers of the btl's.. who get's the
This commit was SVN r11232.
- move files out of toplevel include/ and etc/, moving it into the
sub-projects
- rather than including config headers with <project>/include,
have them as <project>
- require all headers to be included with a project prefix, with
the exception of the config headers ({opal,orte,ompi}_config.h
mpi.h, and mpif.h)
This commit was SVN r8985.
AM_INIT_AUTOMAKE, instead of the deprecated version.
* Work around dumbness in modern AC_INIT that requires the version
number to be set at autoconf time (instead of at configure time, as
it was before). Set the version number, minus the subversion r number,
at autoconf time. Override the internal variables to include the r
number (if needed) at configure time. Basically, the right thing
should always happen. The only place it might not is the version
reported as part of configure --help will not have an r number.
* Since AM_INIT_AUTOMAKE taks a list of options, no need to specify
them in all the Makefile.am files.
* Addes support for subdir-objects, meaning that object files are put
in the directory containing source files, even if the Makefile.am is
in another directory. This should start making it feasible to
reduce the number of Makefile.am files we have in the tree, which
will greatly reduce the time to run autogen and configure.
This commit was SVN r7211.
- After long discussions and ruminations on how we run components in
LAM/MPI, made the decision that, by default, all components included
in Open MPI will use the version number of their parent project
(i.e., OMPI or ORTE). They are certaint free to use a different
number, but this simplification makes the common cases easy:
- components are only released when the parent project is released
- it is easy (trivial?) to distinguish which version component goes
with with version of the parent project
- removed all autogen/configure code for templating the version .h
file in components
- made all ORTE components use ORTE_*_VERSION for version numbers
- made all OMPI components use OMPI_*_VERSION for version numbers
- removed all VERSION files from components
- configure now displays OPAL, ORTE, and OMPI version numbers
- ditto for ompi_info
- right now, faking it -- OPAL and ORTE and OMPI will always have the
same version number (i.e., they all come from the same top-level
VERSION file). But this paves the way for the Great Configure
Reorganization, where, among other things, each project will have
its own version number.
So all in all, we went from a boatload of version numbers to
[effectively] three. That's pretty good. :-)
This commit was SVN r6344.
* rename ompi_malloc to opal_malloc
* rename ompi_numtostr to opal_numtostr
* start of rename of ompi_environ to opal_environ
This commit was SVN r6332.
* rename ompi_basename to opal_basename
* rename ompi bitop functions to opal
* rename ompi_cmd_line to opal_cmd_line
* rename ompi_sizet2int to opal_sizet2int
* rename orte_daemon_init to opal_daemon_init
* rename ompi_few to opal_few
This commit was SVN r6330.
