flex (which, incidentally, emit ''more'' warnings than earlier
versions). Grumble.
This commit was SVN r15166.
The following SVN revision numbers were found above:
r15158 --> open-mpi/ompi@57d09c10f7
branch:
* Support btl_openib_if_include and btl_openib_if_exclude MCA
parameters, similar to those supported by other BTLs. Each take a
comma-delimited lists of identifiers. Identifiers can be HCA
interface names (e.g., ipath0, mthca1, etc.) or an HCA interface
name and port numbers (e.g., ipath0:1, mthca1:2, etc.). It is an
error to specify both _include and _exclude. If you specify a
non-existant (or non-ACTIVE) HCA and/or port, you'll get a warning
unless you disable the warning by setting the MCA parameter
btl_openib_warn_nonexistent_if to 0.
* Start updating to use BEGIN_C_DECLS and END_C_DECLS
* A few other minor fixes that were picked up along the way.
This commit was SVN r15063.
Set bandwidth for all ports of mthca0:
--mca btl_openib_bandwidth_mthca0 1000
Set bandwidth for port 1 of mthca1:
--mca btl_openib_bandwidth_mthca1:1 1000
Set latency for port 2 lid 123 on mthca0:
--mca btl_openib_latency_mthca0:2:123 20
This commit was SVN r15041.
structures in the system. Instead of using memcmp, use the ns function.
This won't cause a problem as long as all three elements of the name are
ints, but if they have different sizes, alignment and padding rules
can cause memcmp() to compare padding space, which rarely holds a sane
value.
This commit was SVN r14998.
id based on the last half of the mapper MAC. This allow us to figure out how
to connect peers. This allow the MX BTL to be used in a cluster of cluster
configuration where each cluster have MX internally as well as on a multi
rail MX system.
This commit was SVN r14932.
symbols in them and environ is defined only in the final application
(probably in crt1.o). Apple provides a function for getting at the
environment, so use that instead if it's available.
This commit was SVN r14857.
have the SRQ interface.
* Instead of setting AC_DEFINEs per MCA component, set per test. THe
answers can never be difference, and this will speed sed just a teeny
bit
This commit was SVN r14856.
This is required to tighten up the BTL semantics. Ordering is not guaranteed,
but, if the BTL returns a order tag in a descriptor (other than
MCA_BTL_NO_ORDER) then we may request another descriptor that will obey
ordering w.r.t. to the other descriptor.
This will allow sane behavior for RDMA networks, where local completion of an
RDMA operation on the active side does not imply remote completion on the
passive side. If we send a FIN message after local completion and the FIN is
not ordered w.r.t. the RDMA operation then badness may occur as the passive
side may now try to deregister the memory and the RDMA operation may still be
pending on the passive side.
Note that this has no impact on networks that don't suffer from this
limitation as the ORDER tag can simply always be specified as
MCA_BTL_NO_ORDER.
This commit was SVN r14768.
fix (r14749) and then backed it out (r14753).
As we are unable to send more than a 32 bits length over TCP in one go, there
is no reason to have an uint64 length in the header. This reduce the size
of the TCP header.
This commit was SVN r14755.
The following SVN revision numbers were found above:
r14749 --> open-mpi/ompi@48c026ce6b
r14753 --> open-mpi/ompi@28ed850b4c
mca_btl_tcp_hdr_t struct and remove the need for the heterogeneous
padding by changing the type of the "size" member to be uint32_t
(vs. uint64_t). The value would never be greater than 32 bits anyway,
so having the type be uint64_t was wasteful.
This commit was SVN r14749.
We eagerly send data up to btl_*_eager_limit with the match
Upon ACK of the MATCH we start using send/receives of size
btl_*_max_send_size up to the btl_*_rdma_pipeline_offset
After the btl_*_rdma_pipeline_offset we begin using RDMA writes of
size btl_*_rdma_pipeline_frag_size.
Now, on a per message basis we only use the above protocol if the
message is larger than btl_*_min_rdma_pipeline_size
btl_*_eager_limit - > same
btl_*_max_send_size -> same
btl_*_rdma_pipeline_offset -> btl_*_min_rdma_size
btl_*_rdma_pipeline_frag_size -> btl_*_max_rdma_size
btl_*_min_rdma_pipeline_size is new..
This patch also moves all BTL common parameters initialisation into
btl_base_mca.c file.
This commit was SVN r14681.
* Move ipv6comat.h code into opal_config_bottom.h and change into some
more intelligent testing of structures
* Change opal's if interface to use sockaddr instead of sockaddr_storage,
as the RFCs suggest we do
* Move the networking code in opal that isn't directly related to if
detection into net.h
* Add quicky function to get the port out of either a sockaddr_in
or sockaddr_in6, saving a bunch of code in the oob.
* Update TCP oob and btl with new interface
This commit was SVN r14679.
without any context so we need to save a context somewhere so it can be
retrieved given only buffer pointer. This patch saves context (pointer to
frag) just before start of a buffer so it can be be easily retrieved.
This commit was SVN r14664.
The following SVN revision numbers were found above:
r13921 --> open-mpi/ompi@90fb58de4f
* Require Autoconf 2.60 or higher and remove some cruft
required for AC 2.59 or the AC 2.59 / AC 2.60 mix
* Remove a bunch of now unnecessary AC_SUBST calls
* Use the libtool-provided variables for the -I and
library to use when compiling against ltdl
Fixes trac:1000
This commit was SVN r14652.
The following Trac tickets were found above:
Ticket 1000 --> https://svn.open-mpi.org/trac/ompi/ticket/1000
avoid alignmment issues. This commit fixes trac:1009.
This commit was SVN r14608.
The following Trac tickets were found above:
Ticket 1009 --> https://svn.open-mpi.org/trac/ompi/ticket/1009
during the IPv6 patch. The most important is the multi BTL support. There
was a quite interesting bug. Instead of setting up the multiple connections
over different physical devices, based on the time when these connections
were created most of the time they were all using the same physical network.
Which, of course, was not the intended goal, as we top at the maximum
bandwidth available over one device instead of gathering all available
bandwidth from all devices.
Second, the IPv6 RFC suggest to use sockaddr_storage as a holder for the
IP information, but use a sockaddr* when we pass it to functions. This is
only partially corrected by this patch.
Some other minor cleanups.
This commit was SVN r14544.
- make opal_sockaddr2str() take a sockaddr_storage instead of a sockaddr_in6
so that it works for IPv4 and IPv6 addresses, and remove a whole bunch
of #ifs in the OOOB code.
- Fix a compiler warning in the TCP BTL due to run-time determined
array size by making it a dynamicly allocated array.
- Fix the unpacking code of IPv4 addresses when using IPv6 support, so
that the address is in the correct location (instead of in an IPv6
structure, use an IPv4 structure). Refs trac:1005.
This commit was SVN r14514.
The following Trac tickets were found above:
Ticket 1005 --> https://svn.open-mpi.org/trac/ompi/ticket/1005
finally brings in functionality that is already on the 1.2 branch, and
was developed and tested in the v1.2ofed branch (and other places).
Short version of new features:
* Support for ibv_fork_init()
* Automatically fill in the openib BTL bandwidth value by
querying the HCA port
* Installdirs functionality
* Fixes to always use -I in the Fortran wrapper compilers (#924)
* Gleb's mpool updates
* Remove some kruft in btl/openib/configure.m4, therefore
fixing the harmless warnings noted in #665
* Bunches of updates to the Linux RPM spec file
I.e., effectively the same thing that r14411 brought to the v1.2
branch.
Also effectively brought in r14432 and r14433 (some fixes on top of
the original r14411 commit to v1.2). Still need to bring in the moral
equivalent of r14445 after this commit (fixes to installdirs).
This commit was SVN r14449.
The following SVN revision numbers were found above:
r14411 --> open-mpi/ompi@83b31314ae
r14432 --> open-mpi/ompi@a48f160595
r14433 --> open-mpi/ompi@68f346d2bc
r14445 --> open-mpi/ompi@13d366b827
Fix for memory corruption in the restarted process stack. This stemed from
the brute force method we were previously using. This commit fixes this by
using a lighter weight solution focused in the r2 BML instead of above the PML.
This is a more efficient and flexible solution, and it solves the original
problem.
In the process I pulled out the ft_event function in the tcp BTL and r2 BML
into a set of *_ft.[c|h] files just to keep any updates to these code paths
as isolated as possible to make merging easier on everyone.
This commit was SVN r14371.
The following SVN revision numbers were found above:
r2 --> open-mpi/ompi@58fdc18855
The following Trac tickets were found above:
Ticket 977 --> https://svn.open-mpi.org/trac/ompi/ticket/977
Per discussions with Brian and Ralph, make a slight correction in
where components are installed. Use $pkglibdir, not $libdir/openmpi,
so that when compiled in the orte trunk, components are installed to
the right directory (because the component search patch is checking
$pkglibdir).
This commit was SVN r14345.
The following SVN revisions from the original message are invalid or
inconsistent and therefore were not cross-referenced:
r14289
the real interest is for small to middle size unexpected messages. The unexpected messages are copied
by the PML in it's own unexpected buffers. Therefore, there is no reason to make a first copy in the
TCP BTL. The BTL can handle to the PML it's own buffer, and can be sure that once the callback
completed it can reuse the buffer, no matter what happened with the fragment.
This commit was SVN r14320.
computation of the current location on the pack/unpack process. This can
be used both for retrieving the pointer to the first byte (in the special
case of the cached RDMA protocol) and for getting the current
position (for the pipelined protocol).
I modified all BTLs, but most of them are still untested.
This commit was SVN r14180.
it limits the number of circular buffers allocated between each pair of peers.
This allows for more tight memory usage control.
This commit was SVN r14120.
waist slightly more memory, but prevents problem when fifo cannot be allocated
later during a job run when memory resource is exhausted.
This commit was SVN r14119.
latency is high and the network relatively fast. This will allow for more kernel
level buffering, which allow overlap between system calls and communications.
Somehow, even on fast clusters there is an improvement (non significant).
This patch create multiple modules for the same device, which in turn will
create multiple sockets between the peers. By default the number of BTL by
device is set to 1, so there is no fundamental difference with the current
version. Change the value of btl_tcp_links to enable multiple links between
peers.
This commit was SVN r14076.
when we precalculate most of the addresses there is no point to have separate
BTL for this. The sm_progress() code become much more simple as a result.
This commit was SVN r14071.
This merge adds Checkpoint/Restart support to Open MPI. The initial
frameworks and components support a LAM/MPI-like implementation.
This commit follows the risk assessment presented to the Open MPI core
development group on Feb. 22, 2007.
This commit closes trac:158
More details to follow.
This commit was SVN r14051.
The following SVN revisions from the original message are invalid or
inconsistent and therefore were not cross-referenced:
r13912
The following Trac tickets were found above:
Ticket 158 --> https://svn.open-mpi.org/trac/ompi/ticket/158
