Retain the hetero-nodes flag for those cases where the user *knows* that there are differences and our automated system isn't good enough to see it.
Will obviously require further refinement as we find out which variances it can detect, and which it cannot.
1. Ensure to override CFLAGS properly. Move the setting of CFLAGS outside the AM_CONDITIONAL so that Automake doesn't get confused (because CFLAGS is already set inside an AM_CONDITIONAL -- moving it outside the conditional ensure that this local CFLAGS override trumps all other CFLAGS overrides).
2. Only build libfabric on Linux. Add a little more configury to ensure that we only try to build libfabric on Linux.
3. Remove a dead/unused file
4. Fix typo in condition check
5. Use "false", not "/bin/false"
This commit represents the conversion of the usnic BTL from verbs to
libfabric.
For the moment, libfabric is embedded in Open MPI (currently in the
usnic BTL). This is because the libfabric API is still changing, and
also has not yet been released. Ultimately, this embedded copy of
libfabric will likely disappear and the usnic BTL will rely on an
external installation of libfabric.
New configure options:
* --with-libfabric: will cause configure to fail if libfabric support
cannot be built
* --without-libfabric: will prevent libfabric support from being built
* --with-libfabric=DIR: use an external libfabric installation
* --with-libfabric-libdir=LIBDIR: when paired with --with-libfabric=DIR,
use LIBDIR for the libfabric installation library dir
The --with-libnl3[-libdir] arguments are now gone.
This commit adds a new class: opal_fifo.h. The new class has atomic, non-atomic,
and opal_using_threads() conditoned routines. It should be used when first-in
first-out is required and should perform much better than using locks and an
opal_list_t. Like with opal_lifo_t there are two versions of the atomic
implementation: 128-bit compare-and-swap, and spin-locked. More implementations
can be added later (LL/SC comes to mind).
This commit also adds a unit test for the opal_fifo_t class. This test verifies
the fifo implementation when using multiple threads.
- Rename opal_atomic_lifo_t to opal_lifo_t to reflect both atomic and
non-atomic usage. Added new routines (opal_lifo_*_st) for non-atomic
usage as well as routines conditioned off opal_using_threads(). The
atomic versions are always thread safe and the non-atomic are always
not thread safe.
- Add a new atomic lifo implementation that makes use of 128-bit
compare-and-swap. The new implementation should scale better with
larger numbers of threads.
- Add threading unit test for opal_lifo_t.
There currently is no standard support for 128-bit integer types. Any use
of the __int128 and int128_t types can lead to warnings from the compiler
when using -Wpedantic. Additionally, some compilers may support __int128
and other may support int128_t. This commit addresses both issues by
defining opal_int128_t if there is a supported 128-bit type. In the
case of GCC a pragma has been added to suppress warnings about __int128
not being a standard C type.
A 128-bit compare-and-swap will enable a better atomic lifo implementation
that uses the pointer + counter method to avoid ABA issues. This commit
adds configury to check for the instruction (cmpxchg16b) and adds an
implementation that uses the __int128 type available in C99.
If OPAL_MODEX_RECV() returns OPAL_ERR_NOT_FOUND, the peer didn't
send any Portals4 BTL info. This is not a fatal error. Instead of
disqualifying the Portals4 BTL just ignore that peer.
@jsquyres reported this in #194.
inserted in the ompi_proc_list as soon as it is created and it
is removed only upon the call to the destructor. In ompi_proc_finalize
we loop over all procs in ompi_proc_finalize and release them once.
However, as a proc is not removed from this list right away, we
decrease the ref count for each proc until it reach zero and the
proc is finally removed. Thus, we cannot clean the BML/BTL after
the call the ompi_proc_finalize.
A quick fix is to delay the call to ompi_proc_finalize until all
other frameworks have been finalized, and then the behavior
depicted above will give the expected outcome.
value NULL for the descriptor
The send inline optimization uses the btl_sendi function to achieve
lower latency and higher message rates. The problem is the btl_sendi
function was allowed to return a descriptor to the caller. This is fine
for some paths but not ok for the send inline optimization. To fix
this the btl now must be able to handle descriptor = NULL.
structure
This structure member was originally used to specify the remote segment
for an RDMA operation. Since the new btl interface no longer uses
desriptors for RDMA this member no longer has a purpose. In addition
to removing these members the local segment information has been
renamed to des_segments/des_segment_count.
The old BTL interface provided support for RDMA through the use of
the btl_prepare_src and btl_prepare_dst functions. These functions were
expected to prepare as much of the user buffer as possible for the RDMA
operation and return a descriptor. The descriptor contained segment
information on the prepared region. The btl user could then pass the
RDMA segment information to a remote peer. Once the peer received that
information it then packed it into a similar descriptor on the other
side that could then be passed into a single btl_put or btl_get
operation.
Changes:
- Removed the btl_prepare_dst function. This reflects the fact that
RDMA operations no longer depend on "prepared" descriptors.
- Removed the btl_seg_size member. There is no need to btl's to
subclass the mca_btl_base_segment_t class anymore.
...
Add more
Use a more reliable way to tell if a process is
1) in a Cray PAGG
2) is actually considered an application process on
a compute node (not for example, a process in a PAGG
on a mom node).
using knem
It is valid to modify the remote segment that will be used with the
btl put/get operations as long as the resulting address range falls in
the originally prepared segment. Vader should have been calculating the
offset of the remote address in the registered region. This commit
fixes this issue.
We recognize that this means other users of OPAL will need to "wrap" the opal_process_name_t if they desire to abstract it in some fashion. This is regrettable, and we are looking at possible alternatives that might mitigate that requirement. Meantime, however, we have to put the needs of the OMPI community first, and are taking this step to restore hetero and SPARC support.
There were mistakes in the Makefiles for the ugni btl and
mca/common/ugni that prevented the ugni btl from being
used unless one happened to set the --disable-dlopen option
on the config line.
This commit fixes this problem.
