Due to IF_NAMESIZE being a reused and conditionally defined macro,
issues could arise from macro mismatches. In particular, in cases where
opal/util/if.h is included, but net/if.h is not, IF_NAMESIZE will be 32.
If net/if.h is included on Linux systems, IF_NAMESIZE will be 16. This
can cause a mismatch when using the same macro on a system. Thus
different parts of the code can have differring ideas on the size of a
structure containing a char name[IF_NAMESIZE]. To avoid this error case,
we avoid reusing the IF_NAMESIZE macro and instead define our own as
OPAL_IF_NAMESIZE.
Signed-off-by: William Zhang <wilzhang@amazon.com>
After the OPAL_MODEX_RECV call, remote_addrs was not freed in the error
path. Moved the free call into cleanup to ensure we always free this
memory before leaving the function.
Signed-off-by: William Zhang <wilzhang@amazon.com>
Remove compatibility code for multiple versions of BTL_IN_OPAL,
BTL_VERSION, and RCACHE_VERSION. This stuff was really only necessary
when we were actively swapping code between multiple release branches
that had large variations in core OMPI infrastructure. These large
variations have now been around for quite a while, so the need for
this "compat" layer is significantly reduced. It hasn't been removed
simply because a few of the "compat" names a slightly more friendly
than the real names (e.g., the SEND/RECV/PUT names).
Signed-off-by: Jeff Squyres <jsquyres@cisco.com>
This commit fixes an error in the 32-bit compare-and-swap atomic support
for Aries networks. The code was incorrectly using the non-fetching
version of cswap which was causing the routing to return
OPAL_ERR_BAD_ARG.
Signed-off-by: Nathan Hjelm <hjelmn@cs.unm.edu>
Avoid printing an error message about ENOTCONN return codes from
getpeername() when handling an incoming connection request. At
this point in the receive state machine, the remote process has
been verified to be a valid OMPI instance. In all-to-all startup
at 4k rank scale, we're seeing this error message when the remote
side drops the connection because it realizes it's the "loser"
in the connection race. We were already doing all the right things,
other than printing a scary error message. So skip the error
message and call it good.
Signed-off-by: Brian Barrett <bbarrett@amazon.com>
free the component mpool in mca_btl_vader_component_close()
and after freeing soem objects that depend on it such as
mca_btl_vader_component.vader_frags_user
Thanks Christoph Niethammer for reporting this.
Refs. open-mpi/ompi#6524
Signed-off-by: Gilles Gouaillardet <gilles@rist.or.jp>
Use $(AM_CPPFLAGS) in $(usnic_btl_run_tests_CPPFLAGS) so that we don't
have to replicate hard-coded values.
Signed-off-by: Jeff Squyres <jsquyres@cisco.com>
do define the OMPI_LIBMPI_NAME macro via the CPPFLAGS.
The issue occurs when Open MPI is configured with
--enable-opal-btl-usnic-unit-tests
Thanks George Marselis for reporting this issue
Refs. open-mpi/ompi#6441
Signed-off-by: Gilles Gouaillardet <gilles@rist.or.jp>
Update the OPAL_CHECK_OFI configury macro:
- Make it safe to call the macro multiple times:
- The checks only execute the first time it is invoked
- Subsequent invocations, it just emits a friendly "checking..."
message so that configure output is sensible/logical
- With the goal of ultimately removing opal/mca/common/ofi, rename the
output variables from OPAL_CHECK_OFI to be
opal_ofi_{happy|CPPFLAGS|LDFLAGS|LIBS}.
- Update btl/ofi, btl/usnic, and mtl/ofi for these new conventions.
- Also, don't use AC_REQUIRE to invoke OPAL_CHECK_OFI because that
causes the macro to be invoked at a fairly random time, which makes
configure stdout confusing / hard to grok.
- Remove a little left-over kruft in OPAL_CHECK_OFI, too (which
resulted in an indenting change, making the change to
opal_check_ofi.m4 look larger than it really is).
Thanks Alastair McKinstry for the report and initial fix.
Thanks Rashika Kheria for the reminder.
Signed-off-by: Jeff Squyres <jsquyres@cisco.com>
So long BTL openib! After many years of (mostly) faithful service, it
is time to remove the openib BTL. It has been fully replaced by other
components, such as the UCX PML and OFI MTL.
Signed-off-by: Jeff Squyres <jsquyres@cisco.com>
It doesn't seem like the BTL was using uninitialized pointer. But simply
setting the rcache pointer to NULL after destroying it makes the valgrind
errors go away.
Fixes Issue #6345
Signed-off-by: Aravind Gopalakrishnan <Aravind.Gopalakrishnan@intel.com>
This commit fixes a bug introduced in
f62d26ddbc. That commit changed how
vader allocates fragment memory from the shared memory
segment. Unfortunately, the values used for the fragment sizes did not
include space for the fragment header. This can cause an overrun of
data from one fragment to the header of the next fragment.
Signed-off-by: Nathan Hjelm <hjelmn@lanl.gov>
This commit updates btl/vader to use an mpool for handling all shared
memory allocations (frags, fboxes).
Signed-off-by: Nathan Hjelm <hjelmn@lanl.gov>
This commit fixes a bug where add_procs can incorrectly return an
error when going through the dynamic add_procs path. This doesn't
happen normally, only when pml/ob1 is not in use.
References #6201
Signed-off-by: Nathan Hjelm <hjelmn@lanl.gov>
remove whitespace around '=' when setting btl_uct_LIBS
Thanks Ake Sandgren for reporting this
Refs. open-mpi/ompi#6173
Signed-off-by: Gilles Gouaillardet <gilles@rist.or.jp>
Though not a recommended configuration it is possible to use Open MPI
over UCX over uGNI. This configuration had some issues related to the
connection management and tl selection. This commit fixes those
issues.
Signed-off-by: Nathan Hjelm <hjelmn@lanl.gov>
If UCX is available, then pml/ucx will be used instead of
pml/ob1 + btl/openib, so there is no need to warn about
btl/openib not supporting Infiniband.
Signed-off-by: Gilles Gouaillardet <gilles@rist.or.jp>
Now Open MPI requires a C99 compiler. Checking availability of
the following types is no more needed.
- `long long` (`signed` and `unsigned`)
- `long double`
- `float _Complex`
- `double _Complex`
- `long double _Complex`
Furthermore, the `#if HAVE_[TYPE]` style checking is not correct.
Availability of C types is checked by `AC_CHECK_TYPES` in `configure.ac`.
`AC_CHECK_TYPES` defines macro `HAVE_[TYPE]` as `1` in `opal_config.h`
if the `[TYPE]` is available. But it does not define `HAVE_[TYPE]`
(instead of defining as `0`) if it is not available. So even if we
need `HAVE_[TYPE]` checking, it should be `#if defined(HAVE_[TYPE])`.
I didn't remove `AC_CHECK_TYPES` for these types in `configure.ac`
since someone may use `HAVE_[TYPE]` macros somewhere.
Signed-off-by: KAWASHIMA Takahiro <t-kawashima@jp.fujitsu.com>
Under certain circumstances, ibv_exp_query_device was
returning an error due to uninitialized fields in the
extended attributes struct.
Fixes: #5810Fixes: #5914
Signed-off-by: Howard Pritchard <howardp@lanl.gov>
In 457f058 I broke the TCP BTL with --enable-ipv6. This patch
fixes the compile error, so IPv6 works again.
Fixed#5996
Signed-off-by: Brian Barrett <bbarrett@amazon.com>
AC_CHECK_DECLS take a comma separated list of macros/symbols,
so replace the whitespace separator with a comma.
Signed-off-by: Gilles Gouaillardet <gilles@rist.or.jp>
Simplify selection of the address to publish for a given BTL TCP
module in the module exchange code. Rather than looping through
all IP addresses associated with a node, looking for one that
matches the kindex of a module, loop over the modules and
use the address stored in the module structure. This also
happens to be the address that the source will use to bind()
in a connect() call, so this should eliminate any confusion
(read: bugs) when an interface has multiple IPs associated with
it.
Refs #5818
Signed-off-by: Brian Barrett <bbarrett@amazon.com>
Today, a btl tcp module is associated with exactly one IP
address (IPv4 or IPv6). There's no need to reserve space
for both an IPv4 and IPv6 address in the module structure,
since the module will only be associated with one or the
other.
Signed-off-by: Brian Barrett <bbarrett@amazon.com>
Work around a race condition in the TCP BTL's proc setup code.
The Cisco MTT results have been failing on TCP tests due to a
"dropped connection" message some percentage of the time.
Some digging shows that the issue happens in a combination of
multiple NICs and multiple threads. The race is detailed in
https://github.com/open-mpi/ompi/issues/3035#issuecomment-429500032.
This patch doesn't fix the race, but avoids it by forcing
the MPI layer to complete all calls to add_procs across the
entire job before any process leaves MPI_INIT. It also
reduces the scalability of the TCP BTL by increasing start-up
time, but better than hanging.
The long term fix is to do all endpoint setup in the first
call to add_procs for a given remote proc, removing the
race. THis patch is a work around until that patch can
be developed.
Signed-off-by: Brian Barrett <bbarrett@amazon.com>
This commit fixes a deadlock that can occur when using a TL that
supports the connect to endpoint model. The deadlock was occurring
while processing an incoming connection requests. This was done from
an active-message callback. For some unknown reason (at this time)
this callback was sometimes hanging. To avoid the issue the connection
active-message is saved for later processing.
At the same time I cleaned up the connection code to eliminate
duplicate messages when possible.
This commit also fixes some bugs in the active-message send path:
- Correctly set all fragment fields in prepare_src.
- Fix bug when using buffered-send. We were not reading the return
code correctly (which is in bytes). This resulted in a message
getting sent multiple times.
- Don't try to progress sends from the btl_send function when in an
active-message callback. It could lead to deep recursion and an
eventual crash if we get a trace like
send->progress->am_complete->ob1_callback->send->am_complete...
Closes#5820Closes#5821
Signed-off-by: Nathan Hjelm <hjelmn@lanl.gov>
This reverts commit 6acebc40a1.
This patch is causing numerous "Socket closed" messages which are
causing most of the failures on Cisco's MTT run. See
https://github.com/open-mpi/ompi/issues/5849 for more information.
Signed-off-by: Brian Barrett <bbarrett@amazon.com>
It is apparently possible for different instances of the same UCT
transport to have different limits (max short put for example). To
account for this we need to store the attributes per TL context not
per TL. This commit fixes the issue.
Signed-off-by: Nathan Hjelm <hjelmn@lanl.gov>
While trying to debug #3035, it's not clear whether there is
an issue with the modex data or printing the address list.
Print the number of endpoints on the error, which will help
determine which case is happening to Cisco.
Signed-off-by: Brian Barrett <bbarrett@amazon.com>
When creating TCP BTL modules, print more information about the
module's ethernet association, including the first address associated
with the device, as debug output.
Fix a flipped output string for IPv4 and IPv6 addresses in the
modex send code.
Add the addresses being published in the modex to the debugging
output in modex send, to help match failures in endpoint match.
Signed-off-by: Brian Barrett <bbarrett@amazon.com>
This commit updates the uct btl to change the transports parameter
into a priority list. The dc_mlx5, rc_mlx5, and ud transports to the
priority list. This will give better out of the box performance for
multi-threaded codes beacuse the *_mlx5 transports can avoid the mlx5
lock inside libmlx5_rdmav2.
This commit also fixes a number of leaks and a possible deadlock when
using RDMA.
Signed-off-by: Nathan Hjelm <hjelmn@lanl.gov>
The Open MPI code base assumed that asprintf always behaved like
the FreeBSD variant, where ptr is set to NULL on error. However,
the C standard (and Linux) only guarantee that the return code will
be -1 on error and leave ptr undefined. Rather than fix all the
usage in the code, we use opal_asprintf() wrapper instead, which
guarantees the BSD-like behavior of ptr always being set to NULL.
In addition to being correct, this will fix many, many warnings
in the Open MPI code base.
Signed-off-by: Brian Barrett <bbarrett@amazon.com>
This commit works around an Oracle C compiler bug in 5.15 (not sure
when it was introduced). The bug is triggered when we chain
assignments of atomic variables. Ex:
_Atomic intptr x, y;
intptr_t z = 0;
x = y = z;
Will produce a compiler error of the form:
operand cannot have void type: op "="
assignment type mismatch:
long "=" void
To work around the issue we are removing the chain assignment and
setting the head and tail on different lines.
Fixes#5814
Signed-off-by: Nathan Hjelm <hjelmn@lanl.gov>
On some platfoms reading a 64-bit value is non-atomic and it is
possible that the two 32-bit values are read in the wrong order. To
ensure the tag is always read first this commit reads the tag before
reading the full 64-bit value.
Signed-off-by: Nathan Hjelm <hjelmn@lanl.gov>
