than just the PML/BTLs these days. Also clean up the code so that it
handles the situation where not all nodes register information for a given
node (rather than just spinning until that node sends information, like
we do today).
Includes r15234 and r15265 from the /tmp/bwb-modex branch.
This commit was SVN r15310.
The following SVN revisions from the original message are invalid or
inconsistent and therefore were not cross-referenced:
r15234
r15265
branch:
* Support btl_openib_if_include and btl_openib_if_exclude MCA
parameters, similar to those supported by other BTLs. Each take a
comma-delimited lists of identifiers. Identifiers can be HCA
interface names (e.g., ipath0, mthca1, etc.) or an HCA interface
name and port numbers (e.g., ipath0:1, mthca1:2, etc.). It is an
error to specify both _include and _exclude. If you specify a
non-existant (or non-ACTIVE) HCA and/or port, you'll get a warning
unless you disable the warning by setting the MCA parameter
btl_openib_warn_nonexistent_if to 0.
* Start updating to use BEGIN_C_DECLS and END_C_DECLS
* A few other minor fixes that were picked up along the way.
This commit was SVN r15063.
Set bandwidth for all ports of mthca0:
--mca btl_openib_bandwidth_mthca0 1000
Set bandwidth for port 1 of mthca1:
--mca btl_openib_bandwidth_mthca1:1 1000
Set latency for port 2 lid 123 on mthca0:
--mca btl_openib_latency_mthca0:2:123 20
This commit was SVN r15041.
have the SRQ interface.
* Instead of setting AC_DEFINEs per MCA component, set per test. THe
answers can never be difference, and this will speed sed just a teeny
bit
This commit was SVN r14856.
finally brings in functionality that is already on the 1.2 branch, and
was developed and tested in the v1.2ofed branch (and other places).
Short version of new features:
* Support for ibv_fork_init()
* Automatically fill in the openib BTL bandwidth value by
querying the HCA port
* Installdirs functionality
* Fixes to always use -I in the Fortran wrapper compilers (#924)
* Gleb's mpool updates
* Remove some kruft in btl/openib/configure.m4, therefore
fixing the harmless warnings noted in #665
* Bunches of updates to the Linux RPM spec file
I.e., effectively the same thing that r14411 brought to the v1.2
branch.
Also effectively brought in r14432 and r14433 (some fixes on top of
the original r14411 commit to v1.2). Still need to bring in the moral
equivalent of r14445 after this commit (fixes to installdirs).
This commit was SVN r14449.
The following SVN revision numbers were found above:
r14411 --> open-mpi/ompi@83b31314ae
r14432 --> open-mpi/ompi@a48f160595
r14433 --> open-mpi/ompi@68f346d2bc
r14445 --> open-mpi/ompi@13d366b827
This merge adds Checkpoint/Restart support to Open MPI. The initial
frameworks and components support a LAM/MPI-like implementation.
This commit follows the risk assessment presented to the Open MPI core
development group on Feb. 22, 2007.
This commit closes trac:158
More details to follow.
This commit was SVN r14051.
The following SVN revisions from the original message are invalid or
inconsistent and therefore were not cross-referenced:
r13912
The following Trac tickets were found above:
Ticket 158 --> https://svn.open-mpi.org/trac/ompi/ticket/158
allocated from mpool memory (which is registered memory for RDMA transports)
This is not a problem for a small jobs, but for a big number of ranks an
amount of waisted memory is big.
This commit was SVN r13921.
and another for dst descriptors. This provide partial solution to OB1 protocol
deadlock problem. We can limit number of RDMA descriptors (by setting
btl_openib_free_list_max to something different from -1) and if we will be
lucky to hit this limit before we fail to register more memory the protocol
will not deadlock. When we had only one list for src/dst descriptors we
deadlocked when we reached max limit for the list.
This commit was SVN r13844.
not the component. This potentially allows for a mix of HCAs that
support eager RDMA and those who do not on a port-by-port basis.
This commit was SVN r13242.
we are looking at subnet_id's and we are counting active ports per subnet.
move subnet count out of procs loop,, no need to do it there...
This commit was SVN r13105.
This is somewhat limited currently for expample, if you have 3 ports on Node A and 5 ports
on Node B then the peers will use 3 ports to communicate with each other.
This is on a subnet basis, so for any pair of nodes we take the
intersection of the available ports within a subnet.
We use subnets to determine reachability for lazy connection establishment. So
if Node A and Node B each have two HCA's (on seperate networks) then the
subnet's must be distinct, otherwise we will try to wire up HCA's on seperate
networks.
This commit was SVN r12978.
* Make sure that the pval always writes to the correct portion of the
lval. This only matters on 32 bit big endian machines.
* On 32 bit machines when assigning to pval, the other 4 bytes of lval
weren't being written, which could lead to bogus data
We use macros so that there aren't casts all over the code and the pval
assignment can occur to the correct 4 bytes. Refs trac:587
This commit was SVN r12974.
The following Trac tickets were found above:
Ticket 587 --> https://svn.open-mpi.org/trac/ompi/ticket/587
udapl/openib/vapi/gm mpools a deprecated. rdma mpool has parameter that allows
to limit its size mpool_rdma_rcache_size_limit (default is 0 - unlimited).
This commit was SVN r12878.
Add ability for ini files to recognize "use_eager_rdma" flag. Set the
default to "no" (because we should assume that HCAs cannot support the
property necessary for using RDMA for eager messages -- that the last
byte of the message is guaranteed to be written to memory last --
unless proven otherwise. For example, iWARP cards apparently do not
provide this guarantee), and then set all Mellanox and IBM HCAs to
override the default to enable this behavior on these cards.
This commit was SVN r12851.
The following Trac tickets were found above:
Ticket 366 --> https://svn.open-mpi.org/trac/ompi/ticket/366
mca_btl_openib_endpoint_connect_eager_rdma() is called recursively. He also
noticed that orte_pointer_array_add() can't fail because we allocate max number
of elements at init time. So just remove error handling and locking. No locking
- no deadlocks.
This commit was SVN r12388.
something is going wrong down in the code it is removed from the array. So add
mutex to prevent concurrent access to the array from different threads.
This commit was SVN r12385.
What's happening is that we're holding openib_btl->eager_rdma_lock when
we call mca_btl_openib_endpoint_send_eager_rdma() on
btl_openib_endpoint.c:1227. This in turn calls
mca_btl_openib_endpoint_send() on line 1179. Then, if the endpoint
state isn't MCA_BTL_IB_CONNECTED or MCA_BTL_IB_FAILED, we call
opal_progress(), where we eventually try to lock
openib_btl->eager_rdma_lock at btl_openib_component.c:997.
The fix removes this lock altogether. Instead we atomically set local RDMA
pointer to prevent other threads to create rdma buffer for the same endpoint.
And we increment eager_rdma_buffers_count atomically thus polling thread doesn't
need lock around it.
This commit was SVN r12369.
GIDs (there can be more than one) and not GIDs of the HCA on the network. Entry
zero always have to be initialized so we use it, and warn user if there is more
then one port active and default subnet is configured on at least one of them.
This commit was SVN r11815.
bunch of code changed indenting level and some code got moved out of
one function and made into its own subroutine.
- Gleb pointed out that I wasn't taking into account values from the
default section of the INI file (and not finding values in the INI
file is not an error).
- I incorrectly thought that 0x5ad was Mellanox's vendor ID. Turns
out that 0x5ad is Cisco's ID, while 0x2c9 is Mellanox.
Specifically, Cisco burns its own firmware into the HCA which
replaces the vendor ID, although the part ID stays the same. So
it's Mellanox hardware with Cisco firmware. And apparently several
of us do that. :-) So I expanded the concept of the vendor_id in
the INI file to allow for lists of vendor IDs.
- Along with that, I updated the default INI file to list all the IB
vendors (that I am aware of -- certainly open to putting more data
in there from other vendors) who overwrite Mellanox's vendor_id with
their own for the part numbers that we have on file.
This commit was SVN r11506.
