Set bandwidth for all ports of mthca0:
--mca btl_openib_bandwidth_mthca0 1000
Set bandwidth for port 1 of mthca1:
--mca btl_openib_bandwidth_mthca1:1 1000
Set latency for port 2 lid 123 on mthca0:
--mca btl_openib_latency_mthca0:2:123 20
This commit was SVN r15041.
structures in the system. Instead of using memcmp, use the ns function.
This won't cause a problem as long as all three elements of the name are
ints, but if they have different sizes, alignment and padding rules
can cause memcmp() to compare padding space, which rarely holds a sane
value.
This commit was SVN r14998.
id based on the last half of the mapper MAC. This allow us to figure out how
to connect peers. This allow the MX BTL to be used in a cluster of cluster
configuration where each cluster have MX internally as well as on a multi
rail MX system.
This commit was SVN r14932.
symbols in them and environ is defined only in the final application
(probably in crt1.o). Apple provides a function for getting at the
environment, so use that instead if it's available.
This commit was SVN r14857.
have the SRQ interface.
* Instead of setting AC_DEFINEs per MCA component, set per test. THe
answers can never be difference, and this will speed sed just a teeny
bit
This commit was SVN r14856.
This is required to tighten up the BTL semantics. Ordering is not guaranteed,
but, if the BTL returns a order tag in a descriptor (other than
MCA_BTL_NO_ORDER) then we may request another descriptor that will obey
ordering w.r.t. to the other descriptor.
This will allow sane behavior for RDMA networks, where local completion of an
RDMA operation on the active side does not imply remote completion on the
passive side. If we send a FIN message after local completion and the FIN is
not ordered w.r.t. the RDMA operation then badness may occur as the passive
side may now try to deregister the memory and the RDMA operation may still be
pending on the passive side.
Note that this has no impact on networks that don't suffer from this
limitation as the ORDER tag can simply always be specified as
MCA_BTL_NO_ORDER.
This commit was SVN r14768.
fix (r14749) and then backed it out (r14753).
As we are unable to send more than a 32 bits length over TCP in one go, there
is no reason to have an uint64 length in the header. This reduce the size
of the TCP header.
This commit was SVN r14755.
The following SVN revision numbers were found above:
r14749 --> open-mpi/ompi@48c026ce6b
r14753 --> open-mpi/ompi@28ed850b4c
mca_btl_tcp_hdr_t struct and remove the need for the heterogeneous
padding by changing the type of the "size" member to be uint32_t
(vs. uint64_t). The value would never be greater than 32 bits anyway,
so having the type be uint64_t was wasteful.
This commit was SVN r14749.
We eagerly send data up to btl_*_eager_limit with the match
Upon ACK of the MATCH we start using send/receives of size
btl_*_max_send_size up to the btl_*_rdma_pipeline_offset
After the btl_*_rdma_pipeline_offset we begin using RDMA writes of
size btl_*_rdma_pipeline_frag_size.
Now, on a per message basis we only use the above protocol if the
message is larger than btl_*_min_rdma_pipeline_size
btl_*_eager_limit - > same
btl_*_max_send_size -> same
btl_*_rdma_pipeline_offset -> btl_*_min_rdma_size
btl_*_rdma_pipeline_frag_size -> btl_*_max_rdma_size
btl_*_min_rdma_pipeline_size is new..
This patch also moves all BTL common parameters initialisation into
btl_base_mca.c file.
This commit was SVN r14681.
* Move ipv6comat.h code into opal_config_bottom.h and change into some
more intelligent testing of structures
* Change opal's if interface to use sockaddr instead of sockaddr_storage,
as the RFCs suggest we do
* Move the networking code in opal that isn't directly related to if
detection into net.h
* Add quicky function to get the port out of either a sockaddr_in
or sockaddr_in6, saving a bunch of code in the oob.
* Update TCP oob and btl with new interface
This commit was SVN r14679.
without any context so we need to save a context somewhere so it can be
retrieved given only buffer pointer. This patch saves context (pointer to
frag) just before start of a buffer so it can be be easily retrieved.
This commit was SVN r14664.
The following SVN revision numbers were found above:
r13921 --> open-mpi/ompi@90fb58de4f
* Require Autoconf 2.60 or higher and remove some cruft
required for AC 2.59 or the AC 2.59 / AC 2.60 mix
* Remove a bunch of now unnecessary AC_SUBST calls
* Use the libtool-provided variables for the -I and
library to use when compiling against ltdl
Fixes trac:1000
This commit was SVN r14652.
The following Trac tickets were found above:
Ticket 1000 --> https://svn.open-mpi.org/trac/ompi/ticket/1000
avoid alignmment issues. This commit fixes trac:1009.
This commit was SVN r14608.
The following Trac tickets were found above:
Ticket 1009 --> https://svn.open-mpi.org/trac/ompi/ticket/1009
during the IPv6 patch. The most important is the multi BTL support. There
was a quite interesting bug. Instead of setting up the multiple connections
over different physical devices, based on the time when these connections
were created most of the time they were all using the same physical network.
Which, of course, was not the intended goal, as we top at the maximum
bandwidth available over one device instead of gathering all available
bandwidth from all devices.
Second, the IPv6 RFC suggest to use sockaddr_storage as a holder for the
IP information, but use a sockaddr* when we pass it to functions. This is
only partially corrected by this patch.
Some other minor cleanups.
This commit was SVN r14544.
