* Resolves#3705
* Components should link against the project level library to better
support `dlopen` with `RTLD_LOCAL`.
* Extend the `mca_FRAMEWORK_COMPONENT_la_LIBADD` in the `Makefile.am`
with the appropriate project level library:
```
MCA components in ompi/
$(top_builddir)/ompi/lib@OMPI_LIBMPI_NAME@.la
MCA components in orte/
$(top_builddir)/orte/lib@ORTE_LIB_PREFIX@open-rte.la
MCA components in opal/
$(top_builddir)/opal/lib@OPAL_LIB_PREFIX@open-pal.la
MCA components in oshmem/
$(top_builddir)/oshmem/liboshmem.la"
```
Note: The changes in this commit were automated by the script in
the commit that proceeds it with the `libadd_mca_comp_update.py`
script. Some components were not included in this change because
they are statically built only.
Signed-off-by: Joshua Hursey <jhursey@us.ibm.com>
Start updating the various mappers to the new procedure. Remove the stale lama component as it is now very out-of-date. Bring round_robin and PPR online, and modify the mindist component (but cannot test/debug it).
Remove unneeded test
Fix memory corruption by re-initializing variable to NULL in loop
Resolve the race condition identified by @ggouaillardet by resetting the
mapped flag within the same event where it was set. There is no need to
retain the flag beyond that point as it isn't used again.
Add a new job attribute ORTE_JOB_FULLY_DESCRIBED to indicate that all the job information (including locations and binding) is included in the launch message. Thus, the backend daemons do not need to do any map computation for the job. Use this for the seq, rankfile, and mindist mappers until someone decides to update them.
Note that this will maintain functionality, but means that users of those three mappers will see large launch messages and less performant scaling than those using the other mappers.
Have the mindist module add procs to the job's proc array as it is a fully described module
Protect the hnp-not-in-allocation case
Per path suggested by Gilles - protect the HNP node when it gets added in the absence of any other allocation or hostfile
Signed-off-by: Ralph Castain <rhc@open-mpi.org>
onto the backend daemons. By default, let mpirun only pack the app_context
info and send that to the backend daemons where the mapping will
be done. This significantly reduces the computational time on mpirun as it isn't
running up/down the topology tree computing thousands of binding
locations, and it reduces the launch message to a very small number of
bytes.
When running -novm, fall back to the old way of doing things
where mpirun computes the entire map and binding, and then sends
the full info to the backend daemon.
Add a new cmd line option/mca param --fwd-mpirun-port that allows
mpirun to dynamically select a port, but then passes that back to
all the other daemons so they will use that port as a static port
for their own wireup. In this mode, we no longer "phone home" directly
to mpirun, but instead use the static port to wireup at daemon
start. We then use the routing tree to rollup the initial
launch report, and limit the number of open sockets on mpirun's node.
Update ras simulator to track the new nidmap code
Cleanup some bugs in the nidmap regex code, and enhance the error message for not enough slots to include the host on which the problem is found.
Update gadget platform file
Initialize the range count when starting a new range
Fix the no-np case in managed allocation
Ensure DVM node usage gets cleaned up after each job
Update scaling.pl script to use --fwd-mpirun-port. Pre-connect the daemon to its parent during launch while we are otherwise waiting for the daemon's children to send their "phone home" rollup messages
Signed-off-by: Ralph Castain <rhc@open-mpi.org>
Cleanup a typo, and remove no longer needed MCA params for hetero nodes and hetero apps. Hetero nodes will always be automatically detected. We don't support a mix of 32 and 64 bit apps
Modify the orte_node_t to use orte_topology_t instead of hwloc_topology_t, updating all the places that use it. Ensure that we properly update topology when we see a different one on a compute node.
Signed-off-by: Ralph Castain <rhc@open-mpi.org>
This commit does two things. It removes checks for C99 required
headers (stdlib.h, string.h, signal.h, etc). Additionally it removes
definitions for required C99 types (intptr_t, int64_t, int32_t, etc).
Signed-off-by: Nathan Hjelm <hjelmn@me.com>
This commit adds an owner file in each of the component directories
for each framework. This allows for a simple script to parse
the contents of the files and generate, among other things, tables
to be used on the project's wiki page. Currently there are two
"fields" in the file, an owner and a status. A tool to parse
the files and generate tables for the wiki page will be added
in a subsequent commit.
Retain the hetero-nodes flag for those cases where the user *knows* that there are differences and our automated system isn't good enough to see it.
Will obviously require further refinement as we find out which variances it can detect, and which it cannot.
http://www.open-mpi.org/community/lists/devel/2014/05/14822.php
Revamp the ORTE global data structures to reduce memory footprint and add new features. Add ability to control/set cpu frequency, though this can only be done if the sys admin has setup the system to support it (or you run as root).
This commit was SVN r31916.
pkg{data,lib,includedir}, use our own ompi{data,lib,includedir}, which is
always set to {datadir,libdir,includedir}/openmpi. This will keep us from
having help files in prefix/share/open-rte when building without Open MPI,
but in prefix/share/openmpi when building with Open MPI.
This commit was SVN r30140.
*** THIS RFC INCLUDES A MINOR CHANGE TO THE MPI-RTE INTERFACE ***
Note: during the course of this work, it was necessary to completely separate the MPI and RTE progress engines. There were multiple places in the MPI layer where ORTE_WAIT_FOR_COMPLETION was being used. A new OMPI_WAIT_FOR_COMPLETION macro was created (defined in ompi/mca/rte/rte.h) that simply cycles across opal_progress until the provided flag becomes false. Places where the MPI layer blocked waiting for RTE to complete an event have been modified to use this macro.
***************************************************************************************
I am reissuing this RFC because of the time that has passed since its original release. Since its initial release and review, I have debugged it further to ensure it fully supports tests like loop_spawn. It therefore seems ready for merge back to the trunk. Given its prior review, I have set the timeout for one week.
The code is in https://bitbucket.org/rhc/ompi-oob2
WHAT: Rewrite of ORTE OOB
WHY: Support asynchronous progress and a host of other features
WHEN: Wed, August 21
SYNOPSIS:
The current OOB has served us well, but a number of limitations have been identified over the years. Specifically:
* it is only progressed when called via opal_progress, which can lead to hangs or recursive calls into libevent (which is not supported by that code)
* we've had issues when multiple NICs are available as the code doesn't "shift" messages between transports - thus, all nodes had to be available via the same TCP interface.
* the OOB "unloads" incoming opal_buffer_t objects during the transmission, thus preventing use of OBJ_RETAIN in the code when repeatedly sending the same message to multiple recipients
* there is no failover mechanism across NICs - if the selected NIC (or its attached switch) fails, we are forced to abort
* only one transport (i.e., component) can be "active"
The revised OOB resolves these problems:
* async progress is used for all application processes, with the progress thread blocking in the event library
* each available TCP NIC is supported by its own TCP module. The ability to asynchronously progress each module independently is provided, but not enabled by default (a runtime MCA parameter turns it "on")
* multi-address TCP NICs (e.g., a NIC with both an IPv4 and IPv6 address, or with virtual interfaces) are supported - reachability is determined by comparing the contact info for a peer against all addresses within the range covered by the address/mask pairs for the NIC.
* a message that arrives on one TCP NIC is automatically shifted to whatever NIC that is connected to the next "hop" if that peer cannot be reached by the incoming NIC. If no TCP module will reach the peer, then the OOB attempts to send the message via all other available components - if none can reach the peer, then an "error" is reported back to the RML, which then calls the errmgr for instructions.
* opal_buffer_t now conforms to standard object rules re OBJ_RETAIN as we no longer "unload" the incoming object
* NIC failure is reported to the TCP component, which then tries to resend the message across any other available TCP NIC. If that doesn't work, then the message is given back to the OOB base to try using other components. If all that fails, then the error is reported to the RML, which reports to the errmgr for instructions
* obviously from the above, multiple OOB components (e.g., TCP and UD) can be active in parallel
* the matching code has been moved to the RML (and out of the OOB/TCP component) so it is independent of transport
* routing is done by the individual OOB modules (as opposed to the RML). Thus, both routed and non-routed transports can simultaneously be active
* all blocking send/recv APIs have been removed. Everything operates asynchronously.
KNOWN LIMITATIONS:
* although provision is made for component failover as described above, the code for doing so has not been fully implemented yet. At the moment, if all connections for a given peer fail, the errmgr is notified of a "lost connection", which by default results in termination of the job if it was a lifeline
* the IPv6 code is present and compiles, but is not complete. Since the current IPv6 support in the OOB doesn't work anyway, I don't consider this a blocker
* routing is performed at the individual module level, yet the active routed component is selected on a global basis. We probably should update that to reflect that different transports may need/choose to route in different ways
* obviously, not every error path has been tested nor necessarily covered
* determining abnormal termination is more challenging than in the old code as we now potentially have multiple ways of connecting to a process. Ideally, we would declare "connection failed" when *all* transports can no longer reach the process, but that requires some additional (possibly complex) code. For now, the code replicates the old behavior only somewhat modified - i.e., if a module sees its connection fail, it checks to see if it is a lifeline. If so, it notifies the errmgr that the lifeline is lost - otherwise, it notifies the errmgr that a non-lifeline connection was lost.
* reachability is determined solely on the basis of a shared subnet address/mask - more sophisticated algorithms (e.g., the one used in the tcp btl) are required to handle routing via gateways
* the RML needs to assign sequence numbers to each message on a per-peer basis. The receiving RML will then deliver messages in order, thus preventing out-of-order messaging in the case where messages travel across different transports or a message needs to be redirected/resent due to failure of a NIC
This commit was SVN r29058.
Features:
- Support for an override parameter file (openmpi-mca-param-override.conf).
Variable values in this file can not be overridden by any file or environment
value.
- Support for boolean, unsigned, and unsigned long long variables.
- Support for true/false values.
- Support for enumerations on integer variables.
- Support for MPIT scope, verbosity, and binding.
- Support for command line source.
- Support for setting variable source via the environment using
OMPI_MCA_SOURCE_<var name>=source (either command or file:filename)
- Cleaner API.
- Support for variable groups (equivalent to MPIT categories).
Notes:
- Variables must be created with a backing store (char **, int *, or bool *)
that must live at least as long as the variable.
- Creating a variable with the MCA_BASE_VAR_FLAG_SETTABLE enables the use of
mca_base_var_set_value() to change the value.
- String values are duplicated when the variable is registered. It is up to
the caller to free the original value if necessary. The new value will be
freed by the mca_base_var system and must not be freed by the user.
- Variables with constant scope may not be settable.
- Variable groups (and all associated variables) are deregistered when the
component is closed or the component repository item is freed. This
prevents a segmentation fault from accessing a variable after its component
is unloaded.
- After some discussion we decided we should remove the automatic registration
of component priority variables. Few component actually made use of this
feature.
- The enumerator interface was updated to be general enough to handle
future uses of the interface.
- The code to generate ompi_info output has been moved into the MCA variable
system. See mca_base_var_dump().
opal: update core and components to mca_base_var system
orte: update core and components to mca_base_var system
ompi: update core and components to mca_base_var system
This commit also modifies the rmaps framework. The following variables were
moved from ppr and lama: rmaps_base_pernode, rmaps_base_n_pernode,
rmaps_base_n_persocket. Both lama and ppr create synonyms for these variables.
This commit was SVN r28236.
Remove some stale configure.m4's we no longer need.
Optimize the nidmaps a bit by only sending info that has changed each time, instead of sending a complete copy of everything. Makes no difference for the typical MPI job - only impacts things like staged execution where we are sending multiple (possibly many) launch messages.
This commit was SVN r27165.
