related to #7128
The UCX crew is no longer guaranteeing that the UCT API is going to be frozen,
so this is kind of a whack-a-mole problem trying to keep the BTL UCT working
with various changing UCT APIs.
Signed-off-by: Howard Pritchard <howardp@lanl.gov>
Move the prefix area from the head to the body in relevant size
computations. This fixes a problem in high traffic situations where
usNIC may have sent from unregistered memory.
Signed-off-by: Jeff Squyres <jsquyres@cisco.com>
New MCA param: btl_usnic_max_resends_per_iteration. This is the max
number of resends we'll do in a single pass through usNIC component
progress. This prevents progress from getting stuck in an endless
loop of retransmissions (i.e., if more retransmissions are triggered
during the sending of retransmissions). Specifically: we need to
leave the resend loop to allow receives to happen (which may ACK
messages we have sent previously, and therefore cause pending resends
to be moot).
Signed-off-by: Jeff Squyres <jsquyres@cisco.com>
Significantly increase the default retrans timeout. If the
retrans timeout is too soon, we can end up in a retransmission storm
where the logic will continually re-transmit the same frames during a
single run through the usNIC progress function (because the timer for
a single frame expires before we have run through re-transmitting all
the frames pending re-transmission).
Signed-off-by: Jeff Squyres <jsquyres@cisco.com>
New MCA parameter: btl_usnic_ack_iteration_delay. Set this to the
number of times through the usNIC component progress function before
sending a standalone ACK (vs. piggy-backing the ACK on any other send
going to the target peer).
Use "ticks" language to clarify that we're really counting the number
of times through the usNIC component DATA_CHANNEL completion check (to
check for incoming messages) -- it has no relation to wall clock time
whatsoever.
Also slightly change the channel-checking scheme in usNIC component
progress: only check the PRIORITY channel once (vs. checking it once,
not finding anything, and then falling through the progress_2() where we
check PRIORITY again and then check the DATA channel).
As before, if our "progress" libevent fires, increment the tick
counter enough to guarantee that all endpoints that need an ACK will
get triggered to send standalone ACKs the next time through progress,
if necessary.
Signed-off-by: Jeff Squyres <jsquyres@cisco.com>
Rename "get_nsec()" to "get_ticks()" to more accurately reflect that
this function has no correlation to wall clock time at all.
Signed-off-by: Jeff Squyres <jsquyres@cisco.com>
Might as well save a few bytes when sending this struct across the
network via the __opal_attribute_packed__ attribute.
That being said, also re-order the elements in this struct so that
there's no holes to begin with. Do this so that the compiler/runtime
won't effect (slow) unaligned reads/writes because of the
__opal_attribute_packed__ attribute.
The "packed" attribute is really more about defensive programming
(e.g., if we make a mistake and have a hole, "packed" will remove it
for us).
*** Do not bring this commit back to existing/already-released release
branches: it will cause incompatibility, since it effectively changes
the usNIC BTL wire protocol.
Signed-off-by: Jeff Squyres <jsquyres@cisco.com>
This commit fixes a crash that can occur if a transport
is usable but doesn't have zero-copy support. In this
case do not attempt to use zero-copy and set the max
send size off the bcopy limit.
Signed-off-by: Nathan Hjelm <hjelmn@google.com>
OpenUCX broke the UCT API again in v1.8. This commit updates
btl/uct to fix compilation with current OpenUCX master
(future v1.8). Further changes will likely be needed for
the final release.
Signed-off-by: Nathan Hjelm <hjelmn@google.com>
This commit changes how the single-copy emulation in the vader btl
operates. Before this change the BTL set its put and get limits
based on the max send size. After this change the limits are unset
and the put or get operation is fragmented internally.
References #6568
Signed-off-by: Nathan Hjelm <hjelmn@google.com>
Trying out to run processes via mpirun in Podman containers has shown
that the CMA btl_vader_single_copy_mechanism does not work when user
namespaces are involved.
Creating containers with Podman requires at least user namespaces to be
able to do unprivileged mounts in a container
Even if running the container with user namespace user ID mappings which
result in the same user ID on the inside and outside of all involved
containers, the check in the kernel to allow ptrace (and thus
process_vm_{read,write}v()), fails if the same IDs are not in the same
user namespace.
One workaround is to specify '--mca btl_vader_single_copy_mechanism none'
and this commit adds code to automatically skip CMA if user namespaces
are detected and fall back to MCA_BTL_VADER_EMUL.
Signed-off-by: Adrian Reber <areber@redhat.com>
Due to IF_NAMESIZE being a reused and conditionally defined macro,
issues could arise from macro mismatches. In particular, in cases where
opal/util/if.h is included, but net/if.h is not, IF_NAMESIZE will be 32.
If net/if.h is included on Linux systems, IF_NAMESIZE will be 16. This
can cause a mismatch when using the same macro on a system. Thus
different parts of the code can have differring ideas on the size of a
structure containing a char name[IF_NAMESIZE]. To avoid this error case,
we avoid reusing the IF_NAMESIZE macro and instead define our own as
OPAL_IF_NAMESIZE.
Signed-off-by: William Zhang <wilzhang@amazon.com>
After the OPAL_MODEX_RECV call, remote_addrs was not freed in the error
path. Moved the free call into cleanup to ensure we always free this
memory before leaving the function.
Signed-off-by: William Zhang <wilzhang@amazon.com>
Remove compatibility code for multiple versions of BTL_IN_OPAL,
BTL_VERSION, and RCACHE_VERSION. This stuff was really only necessary
when we were actively swapping code between multiple release branches
that had large variations in core OMPI infrastructure. These large
variations have now been around for quite a while, so the need for
this "compat" layer is significantly reduced. It hasn't been removed
simply because a few of the "compat" names a slightly more friendly
than the real names (e.g., the SEND/RECV/PUT names).
Signed-off-by: Jeff Squyres <jsquyres@cisco.com>
This commit fixes an error in the 32-bit compare-and-swap atomic support
for Aries networks. The code was incorrectly using the non-fetching
version of cswap which was causing the routing to return
OPAL_ERR_BAD_ARG.
Signed-off-by: Nathan Hjelm <hjelmn@cs.unm.edu>
Avoid printing an error message about ENOTCONN return codes from
getpeername() when handling an incoming connection request. At
this point in the receive state machine, the remote process has
been verified to be a valid OMPI instance. In all-to-all startup
at 4k rank scale, we're seeing this error message when the remote
side drops the connection because it realizes it's the "loser"
in the connection race. We were already doing all the right things,
other than printing a scary error message. So skip the error
message and call it good.
Signed-off-by: Brian Barrett <bbarrett@amazon.com>
free the component mpool in mca_btl_vader_component_close()
and after freeing soem objects that depend on it such as
mca_btl_vader_component.vader_frags_user
Thanks Christoph Niethammer for reporting this.
Refs. open-mpi/ompi#6524
Signed-off-by: Gilles Gouaillardet <gilles@rist.or.jp>
Use $(AM_CPPFLAGS) in $(usnic_btl_run_tests_CPPFLAGS) so that we don't
have to replicate hard-coded values.
Signed-off-by: Jeff Squyres <jsquyres@cisco.com>
do define the OMPI_LIBMPI_NAME macro via the CPPFLAGS.
The issue occurs when Open MPI is configured with
--enable-opal-btl-usnic-unit-tests
Thanks George Marselis for reporting this issue
Refs. open-mpi/ompi#6441
Signed-off-by: Gilles Gouaillardet <gilles@rist.or.jp>
Update the OPAL_CHECK_OFI configury macro:
- Make it safe to call the macro multiple times:
- The checks only execute the first time it is invoked
- Subsequent invocations, it just emits a friendly "checking..."
message so that configure output is sensible/logical
- With the goal of ultimately removing opal/mca/common/ofi, rename the
output variables from OPAL_CHECK_OFI to be
opal_ofi_{happy|CPPFLAGS|LDFLAGS|LIBS}.
- Update btl/ofi, btl/usnic, and mtl/ofi for these new conventions.
- Also, don't use AC_REQUIRE to invoke OPAL_CHECK_OFI because that
causes the macro to be invoked at a fairly random time, which makes
configure stdout confusing / hard to grok.
- Remove a little left-over kruft in OPAL_CHECK_OFI, too (which
resulted in an indenting change, making the change to
opal_check_ofi.m4 look larger than it really is).
Thanks Alastair McKinstry for the report and initial fix.
Thanks Rashika Kheria for the reminder.
Signed-off-by: Jeff Squyres <jsquyres@cisco.com>
So long BTL openib! After many years of (mostly) faithful service, it
is time to remove the openib BTL. It has been fully replaced by other
components, such as the UCX PML and OFI MTL.
Signed-off-by: Jeff Squyres <jsquyres@cisco.com>
It doesn't seem like the BTL was using uninitialized pointer. But simply
setting the rcache pointer to NULL after destroying it makes the valgrind
errors go away.
Fixes Issue #6345
Signed-off-by: Aravind Gopalakrishnan <Aravind.Gopalakrishnan@intel.com>
This commit fixes a bug introduced in
f62d26ddbc. That commit changed how
vader allocates fragment memory from the shared memory
segment. Unfortunately, the values used for the fragment sizes did not
include space for the fragment header. This can cause an overrun of
data from one fragment to the header of the next fragment.
Signed-off-by: Nathan Hjelm <hjelmn@lanl.gov>
This commit updates btl/vader to use an mpool for handling all shared
memory allocations (frags, fboxes).
Signed-off-by: Nathan Hjelm <hjelmn@lanl.gov>
This commit fixes a bug where add_procs can incorrectly return an
error when going through the dynamic add_procs path. This doesn't
happen normally, only when pml/ob1 is not in use.
References #6201
Signed-off-by: Nathan Hjelm <hjelmn@lanl.gov>
remove whitespace around '=' when setting btl_uct_LIBS
Thanks Ake Sandgren for reporting this
Refs. open-mpi/ompi#6173
Signed-off-by: Gilles Gouaillardet <gilles@rist.or.jp>
Though not a recommended configuration it is possible to use Open MPI
over UCX over uGNI. This configuration had some issues related to the
connection management and tl selection. This commit fixes those
issues.
Signed-off-by: Nathan Hjelm <hjelmn@lanl.gov>
If UCX is available, then pml/ucx will be used instead of
pml/ob1 + btl/openib, so there is no need to warn about
btl/openib not supporting Infiniband.
Signed-off-by: Gilles Gouaillardet <gilles@rist.or.jp>
