parameters on the connecting side also. Also move define of IF_NAMESIZE
into if.h file. And lastly, add one verbose debug message which may be
useful if we run into other issues like this.
This commit fixes trac:1573.
This commit was SVN r19932.
The following Trac tickets were found above:
Ticket 1573 --> https://svn.open-mpi.org/trac/ompi/ticket/1573
* add "register" function to mca_base_component_t
* converted coll:basic and paffinity:linux and paffinity:solaris to
use this function
* we'll convert the rest over time (I'll file a ticket once all
this is committed)
* add 32 bytes of "reserved" space to the end of mca_base_component_t
and mca_base_component_data_2_0_0_t to make future upgrades
[slightly] easier
* new mca_base_component_t size: 196 bytes
* new mca_base_component_data_2_0_0_t size: 36 bytes
* MCA base version bumped to v2.0
* '''We now refuse to load components that are not MCA v2.0.x'''
* all MCA frameworks versions bumped to v2.0
* be a little more explicit about version numbers in the MCA base
* add big comment in mca.h about versioning philosophy
This commit was SVN r19073.
The following Trac tickets were found above:
Ticket 1392 --> https://svn.open-mpi.org/trac/ompi/ticket/1392
After much work by Jeff and myself, and quite a lot of discussion, it has become clear that we simply cannot resolve the infinite loops caused by RML-involved subsystems calling orte_output. The original rationale for the change to orte_output has also been reduced by shifting the output of XML-formatted vs human readable messages to an alternative approach.
I have globally replaced the orte_output/ORTE_OUTPUT calls in the code base, as well as the corresponding .h file name. I have test compiled and run this on the various environments within my reach, so hopefully this will prove minimally disruptive.
This commit was SVN r18619.
such, the commit message back to the master SVN repository is fairly
long.
= ORTE Job-Level Output Messages =
Add two new interfaces that should be used for all new code throughout
the ORTE and OMPI layers (we already make the search-and-replace on
the existing ORTE / OMPI layers):
* orte_output(): (and corresponding friends ORTE_OUTPUT,
orte_output_verbose, etc.) This function sends the output directly
to the HNP for processing as part of a job-specific output
channel. It supports all the same outputs as opal_output()
(syslog, file, stdout, stderr), but for stdout/stderr, the output
is sent to the HNP for processing and output. More on this below.
* orte_show_help(): This function is a drop-in-replacement for
opal_show_help(), with two differences in functionality:
1. the rendered text help message output is sent to the HNP for
display (rather than outputting directly into the process' stderr
stream)
1. the HNP detects duplicate help messages and does not display them
(so that you don't see the same error message N times, once from
each of your N MPI processes); instead, it counts "new" instances
of the help message and displays a message every ~5 seconds when
there are new ones ("I got X new copies of the help message...")
opal_show_help and opal_output still exist, but they only output in
the current process. The intent for the new orte_* functions is that
they can apply job-level intelligence to the output. As such, we
recommend that all new ORTE and OMPI code use the new orte_*
functions, not thei opal_* functions.
=== New code ===
For ORTE and OMPI programmers, here's what you need to do differently
in new code:
* Do not include opal/util/show_help.h or opal/util/output.h.
Instead, include orte/util/output.h (this one header file has
declarations for both the orte_output() series of functions and
orte_show_help()).
* Effectively s/opal_output/orte_output/gi throughout your code.
Note that orte_output_open() takes a slightly different argument
list (as a way to pass data to the filtering stream -- see below),
so you if explicitly call opal_output_open(), you'll need to
slightly adapt to the new signature of orte_output_open().
* Literally s/opal_show_help/orte_show_help/. The function signature
is identical.
=== Notes ===
* orte_output'ing to stream 0 will do similar to what
opal_output'ing did, so leaving a hard-coded "0" as the first
argument is safe.
* For systems that do not use ORTE's RML or the HNP, the effect of
orte_output_* and orte_show_help will be identical to their opal
counterparts (the additional information passed to
orte_output_open() will be lost!). Indeed, the orte_* functions
simply become trivial wrappers to their opal_* counterparts. Note
that we have not tested this; the code is simple but it is quite
possible that we mucked something up.
= Filter Framework =
Messages sent view the new orte_* functions described above and
messages output via the IOF on the HNP will now optionally be passed
through a new "filter" framework before being output to
stdout/stderr. The "filter" OPAL MCA framework is intended to allow
preprocessing to messages before they are sent to their final
destinations. The first component that was written in the filter
framework was to create an XML stream, segregating all the messages
into different XML tags, etc. This will allow 3rd party tools to read
the stdout/stderr from the HNP and be able to know exactly what each
text message is (e.g., a help message, another OMPI infrastructure
message, stdout from the user process, stderr from the user process,
etc.).
Filtering is not active by default. Filter components must be
specifically requested, such as:
{{{
$ mpirun --mca filter xml ...
}}}
There can only be one filter component active.
= New MCA Parameters =
The new functionality described above introduces two new MCA
parameters:
* '''orte_base_help_aggregate''': Defaults to 1 (true), meaning that
help messages will be aggregated, as described above. If set to 0,
all help messages will be displayed, even if they are duplicates
(i.e., the original behavior).
* '''orte_base_show_output_recursions''': An MCA parameter to help
debug one of the known issues, described below. It is likely that
this MCA parameter will disappear before v1.3 final.
= Known Issues =
* The XML filter component is not complete. The current output from
this component is preliminary and not real XML. A bit more work
needs to be done to configure.m4 search for an appropriate XML
library/link it in/use it at run time.
* There are possible recursion loops in the orte_output() and
orte_show_help() functions -- e.g., if RML send calls orte_output()
or orte_show_help(). We have some ideas how to fix these, but
figured that it was ok to commit before feature freeze with known
issues. The code currently contains sub-optimal workarounds so
that this will not be a problem, but it would be good to actually
solve the problem rather than have hackish workarounds before v1.3 final.
This commit was SVN r18434.
- the registration array is now global instead of one by BTL.
- each framework have to declare the entries in the registration array reserved. Then
it have to define the internal way of sharing (or not) these entries between all
components. As an example, the PML will not share as there is only one active PML
at any moment, while the BTLs will have to. The tag is 8 bits long, the first 3
are reserved for the framework while the remaining 5 are use internally by each
framework.
- The registration function is optional. If a BTL do not provide such function,
nothing happens. However, in the case where such function is provided in the BTL
structure, it will be called by the BML, when a tag is registered.
Now, it's time for the second step... Converting OB1 from a switch based PML to an
active message one.
This commit was SVN r17140.
has his own range which is defined by a min value and a range. By default
there is no limitation on the port range, which is exactly the same
behavior as before.
This commit was SVN r16584.
the ompi_convertor_need_buffers function to only return 0 if the convertor
is homogeneous (which it never does on the trunk, but does to on v1.2, but
that's a different issue). Only enable the heterogeneous rdma code for
a btl if it supports it (via a flag), as some btls need some work for this
to work properly. Currently only TCP and OpenIB extensively tested
This commit was SVN r15990.
than just the PML/BTLs these days. Also clean up the code so that it
handles the situation where not all nodes register information for a given
node (rather than just spinning until that node sends information, like
we do today).
Includes r15234 and r15265 from the /tmp/bwb-modex branch.
This commit was SVN r15310.
The following SVN revisions from the original message are invalid or
inconsistent and therefore were not cross-referenced:
r15234
r15265
We eagerly send data up to btl_*_eager_limit with the match
Upon ACK of the MATCH we start using send/receives of size
btl_*_max_send_size up to the btl_*_rdma_pipeline_offset
After the btl_*_rdma_pipeline_offset we begin using RDMA writes of
size btl_*_rdma_pipeline_frag_size.
Now, on a per message basis we only use the above protocol if the
message is larger than btl_*_min_rdma_pipeline_size
btl_*_eager_limit - > same
btl_*_max_send_size -> same
btl_*_rdma_pipeline_offset -> btl_*_min_rdma_size
btl_*_rdma_pipeline_frag_size -> btl_*_max_rdma_size
btl_*_min_rdma_pipeline_size is new..
This patch also moves all BTL common parameters initialisation into
btl_base_mca.c file.
This commit was SVN r14681.
* Move ipv6comat.h code into opal_config_bottom.h and change into some
more intelligent testing of structures
* Change opal's if interface to use sockaddr instead of sockaddr_storage,
as the RFCs suggest we do
* Move the networking code in opal that isn't directly related to if
detection into net.h
* Add quicky function to get the port out of either a sockaddr_in
or sockaddr_in6, saving a bunch of code in the oob.
* Update TCP oob and btl with new interface
This commit was SVN r14679.
during the IPv6 patch. The most important is the multi BTL support. There
was a quite interesting bug. Instead of setting up the multiple connections
over different physical devices, based on the time when these connections
were created most of the time they were all using the same physical network.
Which, of course, was not the intended goal, as we top at the maximum
bandwidth available over one device instead of gathering all available
bandwidth from all devices.
Second, the IPv6 RFC suggest to use sockaddr_storage as a holder for the
IP information, but use a sockaddr* when we pass it to functions. This is
only partially corrected by this patch.
Some other minor cleanups.
This commit was SVN r14544.
- make opal_sockaddr2str() take a sockaddr_storage instead of a sockaddr_in6
so that it works for IPv4 and IPv6 addresses, and remove a whole bunch
of #ifs in the OOOB code.
- Fix a compiler warning in the TCP BTL due to run-time determined
array size by making it a dynamicly allocated array.
- Fix the unpacking code of IPv4 addresses when using IPv6 support, so
that the address is in the correct location (instead of in an IPv6
structure, use an IPv4 structure). Refs trac:1005.
This commit was SVN r14514.
The following Trac tickets were found above:
Ticket 1005 --> https://svn.open-mpi.org/trac/ompi/ticket/1005
latency is high and the network relatively fast. This will allow for more kernel
level buffering, which allow overlap between system calls and communications.
Somehow, even on fast clusters there is an improvement (non significant).
This patch create multiple modules for the same device, which in turn will
create multiple sockets between the peers. By default the number of BTL by
device is set to 1, so there is no fundamental difference with the current
version. Change the value of btl_tcp_links to enable multiple links between
peers.
This commit was SVN r14076.
This merge adds Checkpoint/Restart support to Open MPI. The initial
frameworks and components support a LAM/MPI-like implementation.
This commit follows the risk assessment presented to the Open MPI core
development group on Feb. 22, 2007.
This commit closes trac:158
More details to follow.
This commit was SVN r14051.
The following SVN revisions from the original message are invalid or
inconsistent and therefore were not cross-referenced:
r13912
The following Trac tickets were found above:
Ticket 158 --> https://svn.open-mpi.org/trac/ompi/ticket/158
r12714) for supporting compilers / architectures with different
padding rules.
This commit was SVN r12749.
The following SVN revisions from the original message are invalid or
inconsistent and therefore were not cross-referenced:
r12491
r12714
hits the buffer on the other side. For this kind of BTLs we need to send
FIN through the same BTL, PUT was performed with so network will handle
ordering for us. If we will use another BTL, receiver can get FIN before
data will hit the buffer and complete request prematurely. We mark such
problematic BTLs with MCA_BTL_FLAGS_FAKE_RDMA flag (this kind of RDMA
is really fake, because the real one guaranties that sender will see the
completion only after receiver's NIC confirmed that all the data was
received).
This commit was SVN r12732.
because they are in ORTE, not OMPI. Also, remove the ORTE_PROCESS_NAME macros
in iof base as they are duplicates of the ones that were in ns_types, which
meant that bad things happened if you changed what an orte_process_name_t
looked like.
This commit was SVN r12646.
In order to provide backwards compatability the framework versions are bumped
and the handler registeration function is at the end of the btl struct.
Testing done on sm, openib, and gm..
This commit was SVN r11256.
the upperlayer assynchronously although there are some issues with this.. such
as there are multiple consumers of the btl's.. who get's the
This commit was SVN r11232.
Instead of figuring out which free list the fragment belongs to based on size
we simply store a pointer to the list which it belongs in the fragment.
This was reviewed by Brian and should hit all the branches.
This commit was SVN r10072.
